Clarion iDXZ775USB User Manual

This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference in a  
residential installation.  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is encouraged to consult the dealer or an  
experienced radio/TV technician for help.  
Owner’s manual  
Mode d’emploi  
Manual de instrucciones  
Cet appareil a été testé et jugé conforme aux limites des appareils numériques de Classe B, aux  
termes de la Section 15 des Règlements FCC.  
Ces limites ont pour but d’assurer une protection raisonnable contre les interférences parasites  
dans une installation résidentielle.  
Cet appareil engendre, utilise et peut émettre une énergie radioélectrique et, s’il n’est pas installé  
et utilisé en stricte conformité avec ces instructions, il peut provoquer des interférences parasites  
sur les liaisons radiophoniques. Ceci ne garantit par pour autant qu’une installation particulière ne  
provoquera aucune interférence.  
Si l’appareil engendre des interférences sur la réception des ondes radio ou de télévision, ce qui  
peut être vérifié en mettant l’appareil hors tension puis sous tension, l’utilisateur est invité à  
consulter son revendeur ou un technicien exprimenté en radio/télévision pour lui demander conseil.  
DXZ775USB  
Este equipo ha sido probado y se ha comprobado que cumple con los límites de un dispositivo  
digital de clase B, según lo indicado en la Parte 15 de las Normas de FCC.  
Estos límites se han establecido para ofrecer una protección razonable contra interferencias  
perjudiciales en instalaciones residenciales.  
Este equipo genera, emplea, y puede radiar energía de radiofrecuencia y, si no se instala y emplea  
de acuerdo con las instrucciones, puede causar interferencias perjudiciales en las  
radiocomunicaciones. Sin embargo, no se garantiza que las interferencias no ocurran en una  
instalación en particular.  
Si este equipo causa interferencias perjudiciales en la recepción de radio o de televisión, lo cual  
podrá determinarse conectando y desconectando la alimentación del equipo, se aconseja al  
usuario que consulte al abastecedor o que pida ayuda a un técnico en radio/televisión  
experimentado.  
CD/USB/MP3/WMA/AAC RECEIVER WITH CeNET CONTROL  
AUTORADIO CD/USB/MP3/WMA / AVEC COMMANDE CeNET  
RECEPTOR DE CD/USB/MP3/WMA/AAC CON CONTROL CeNET  
Bottom View of Source Unit  
Fond de l’appareil pilote  
Vista inferior de la unidad fuente  
Be sure to unfold and read the next page.  
Veuillez déplier et vous référer à la page suivante.  
Cerciórese de desplegar y de leer la página siguiente.  
DXZ775USB  
i
CLARION PRODUCT REGISTRATION INFORMATION  
CONTROLS / LES COMMANDES / CONTROLES  
For USA and Canada only  
Source unit / Appareil pilote / Unidad fuente  
Dear Customer:  
[
]
[
MENU  
Congratulations on your purchase of a Clarion mobile electronic products. We are  
confident that you’ll enjoy your Clarion experience.  
[
]
OPTION  
]
ENT  
[
]
There are many benefits to registering your product. We invite you to visit our website at  
SRC  
[
]
SEEK PANEL  
www.clarion.com to register your Clarion product.  
[
]
RELEASE  
We have made product registration simple with our easy to use website. The registration  
form is short and easy to complete. Once you’re registered, we can keep you informed of  
important product information.  
Register at www.clarion.com - it’s easy to keep your Clarion product up to date.  
[
]
VOL  
[
]
P.CH  
INFORMATIONS DE L’ENREGISTREMENT DE PRODUITS CLARION  
Pour les Étas Unis et le Canada seulement  
Cher client:  
[
] (SOUND)  
[
] (EJECT)  
] (MUTE)  
Nous vous remercions d’avoir acheté ce produit électronique mobile Clarion. Nous  
sommes confiants que vous apprécierez votre expérience Clarion.  
[
]
ISR  
[
Il y a beaucoup d’avantage à enregistrer votre produits. Nous vous invitons à visiter notre  
site Web www.clarion.com pour enregistrer votre produit Clarion.  
[
]
IR RECEIVER  
[
]
TITLE  
Nous avons facilité la tache d’enregistrement de produit simple et facile grâce à notre  
site Web. Le formulaire d’enregistrement est court et facile à compléter. Lorsque vous  
êtes enregistrer, nous pouvons vous tenir informé des informations important de produits.  
With the MOTORIZED FACE opened/ Ouvrez la FACE MOTORISÉE  
Apertura del FRONTAL MOTORIZADO  
Enregistrer à www.clarion.com - c’est facile de mettre à jour votre produit Clarion.  
[CD SLOT]  
INFORMACIÓN DEL REGISTRO DE PRODUCTO DE CLARION  
Para USA y Canada nomas  
Querido Cliente:  
Felicitaciones por su compra de producto electrónico móvil de Clarion. Estamos seguros  
que usted gozará de su experiencia con el producto de Clarion.  
Hay muchas ventajas al registrar su producto. Le invitamos a que visite nuestro sitio en  
internet www.clarion.com para registrar su producto de Clarion.  
Hemos hecho el registro de producto fácil en nuestro sitio. La forma de registro es corta  
y fácil de completar. Una vez que lo registre, podremos proporcionarle la información de  
su producto.  
Registrese en www.clarion.com - es fácil mantener su producto de Clarion actualizado.  
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.  
Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.  
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.  
ii  
DXZ775USB  
iii  
DXZ775USB  
Thank you for purchasing this Clarion product.  
Please read this owner’s manual in its entirety before operating this equipment.  
After reading this manual, be sure to keep it in a handy place (e.g., glove compartment).  
Check the contents of the enclosed warranty card and keep it carefully with this manual.  
®
This manual includes the operating procedures of the iPod interface, CD/DVD changer, Satellite  
Radio Receiver and TV tuner connected via the CeNET cable. The iPod interface, CD/DVD changer  
and TV tuner have their own manuals, but no explanations for operating them are described.  
“iPod” is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.  
Contents  
CONTROLS............................................................................................................................................ ii  
1. FEATURES...................................................................................................................................... 1  
2. PRECAUTIONS ............................................................................................................................... 2  
Motorized Face................................................................................................................................. 2  
Handling Compact Discs.................................................................................................................. 3  
3. NOMENCLATURE........................................................................................................................... 4  
Names of the Buttons and Their Functions...................................................................................... 4  
Display Items.................................................................................................................................... 5  
LCD Screen...................................................................................................................................... 5  
4. DCP.................................................................................................................................................. 6  
5. REMOTE CONTROL ....................................................................................................................... 7  
Inserting the Battery ......................................................................................................................... 7  
Functions of Remote Control Unit Buttons....................................................................................... 8  
6. OPERATIONS................................................................................................................................ 10  
Basic Operations............................................................................................................................ 10  
Radio Operations ........................................................................................................................... 20  
CD/MP3/WMA/AAC Operations..................................................................................................... 22  
Operations Common to Each Mode............................................................................................... 26  
7. OPERATIONS OF ACCESSORIES .............................................................................................. 30  
USB Operations ............................................................................................................................. 30  
iPod BB Operations........................................................................................................................ 32  
Satellite Radio Operations.............................................................................................................. 34  
CD Changer Operations................................................................................................................. 36  
DVD Changer Operations .............................................................................................................. 38  
TV Operations ................................................................................................................................ 39  
8. IN CASE OF DIFFICULTY............................................................................................................. 40  
9. ERROR DISPLAYS ....................................................................................................................... 42  
10. SPECIFICATIONS ......................................................................................................................... 43  
1. FEATURES  
• Digital Time Alignment Control with 3-way Crossover  
• Motorized Full Dot LCD with SLIDETRAK  
• 6ch/6V RCA Output / 53W X 4 Built-in MOSFET Amplifier  
DXZ775USB  
1
2. PRECAUTIONS  
1. When the inside of the car is very cold and  
the player is used soon after switching on the  
heater moisture may form on the disc or the  
optical parts of the player and proper  
CAUTION  
USE OF CONTROLS, ADJUSTMENTS, OR  
PERFORMANCE OF PROCEDURES OTHER  
THAN THOSE SPECIFIED HEREIN, MAY  
RESULT IN HAZARDOUS RADIATION  
EXPOSURE.  
playback may not be possible. If moisture  
forms on the disc, wipe it off with a soft cloth.  
If moisture forms on the optical parts of the  
player, do not use the player for about one  
hour. The condensation will disappear  
naturally allowing normal operation.  
THE COMPACT DISC PLAYER SHOULD NOT  
BE ADJUSTED OR REPAIRED BY ANYONE  
EXCEPT PROPERLY QUALIFIED SERVICE  
PERSONNEL.  
2. Driving on extremely bumpy roads which  
cause severe vibration may cause the sound  
to skip.  
CHANGES OR MODIFICATIONS NOT  
EXPRESSLY APPROVED BY THE  
MANUFACTURER FOR COMPLIANCE  
COULD VOID THE USER’S AUTHORITY TO  
OPERATE THE EQUIPMENT.  
3. This unit uses a precision mechanism. Even  
in the event that trouble arises, never open  
the case, disassemble the unit, or lubricate  
the rotating parts.  
INFORMATION FOR USERS:  
CHANGES OR MODIFICATIONS TO THIS  
PRODUCT NOT APPROVED BY THE  
MANUFACTURER WILL VOID THE  
WARRANTY AND WILL VIOLATE FCC  
APPROVAL.  
Motorized Face  
This unit uses motorized face to make large-screen displays possible.  
When you use the motorized face, be sure to close it.  
3. If you move the MOTORIZED FACE by  
CAUTION  
BE CAREFUL NOT TO GET YOUR FINGERS  
CAUGHT WHEN OPENING AND CLOSING  
THE MOTORIZED FACE.  
hand, this may create play. To correct this  
play, with the power on for the unit, press the  
[Q] button to close the MOTORIZED FACE.  
4. After a disc is ejected, the MOTORIZED  
FACE automatically returns to the tilted or  
closed state. If there is any obstruction when  
the MOTORIZED FACE tries to close, the  
safety mechanism is triggered and the  
MOTORIZED FACE returns to the open  
state. If this happens, remove the  
1. For safety’s sake, always close the  
MOTORIZED FACE before leaving this unit  
unused for a prolonged period or switching  
OFF the ignition key.  
If you switch OFF the ignition key with the  
MOTORIZED FACE tilted, the MOTORIZED  
FACE does not close.  
obstruction, then press the [Q] button.  
5. To avoid scratching the compact disk, keep  
the CD level when inserting or removing  
them.  
2. Before the MOTORIZED FACE closes, there  
may be a braking sound from the safety  
mechanism. This is normal.  
2
DXZ775USB  
Handling Compact Discs  
Use only compact discs bearing the  
or  
Storage  
• Do not expose compact discs to direct  
sunlight or any heat source.  
mark.  
Do not play heart-shaped, octagonal, or other  
specially shaped compact discs.  
• Do not expose compact discs to excess  
humidity or dust.  
Some CDs recorded in CD-R/CD-RW mode  
may not be usable.  
• Do not expose compact discs to direct heat  
from heaters.  
Handling  
Cleaning  
• Compared to ordinary music CDs, CD-R and  
CD-RW discs are both easily affected by high  
temperature and humidity and some of CD-R  
and CD-RW discs may not be played.  
Therefore, do not leave them for a long time  
in the car.  
• To remove fingermarks and dust, use a soft  
cloth and wipe in a straight line from the  
center of the compact disc to the  
circumference.  
• Do not use any solvents, such as  
commercially available cleaners, anti-static  
spray, or thinner to clean compact discs.  
• New discs may  
Ball-point pen  
have some  
• After using special compact disc cleaner, let  
the compact disc dry off well before playing it.  
roughness  
Roughness  
around the  
edges. If such  
discs are used,  
the player may  
not work or the  
sound may skip. Use a ball-point pen or the  
like to remove any roughness from the edge  
of the disc.  
• Never stick labels on the surface of the  
compact disc or mark the surface with a  
pencil or pen.  
• Never play a compact disc with any  
cellophane tape or other glue on it or with  
peeling off marks. If you try to play such a  
compact disc, you may not be able to get it  
back out of the CD player or it may damage  
the CD player.  
• Do not use compact discs that have large  
scratches, are misshapen, cracked, etc. Use  
of such discs may cause misoperation or  
damage.  
• To remove a compact disc from its storage  
case, press down on the center of the case  
and lift the disc out, holding it carefully by the  
edges.  
• Do not use commercially available CD  
protection sheets or discs equipped with  
stabilizers, etc. These may damage the disc  
or cause breakdown of the internal  
mechanism.  
DXZ775USB  
3
3. NOMENCLATURE  
Note:  
• Be sure to read this chapter referring to the front diagrams of chapter “CONTROLS” on page ii (unfold).  
Names of the Buttons and Their Functions  
[RELEASE] button  
• Deeply push in the button to unlock the DCP.  
[P.CH] button  
• Push the button upward or downward to recall  
the stored station while in the radio mode.  
[SRC] button  
• Press the button to turn on the power.  
• Select the folder while in the MP3/WMA/AAC  
mode.  
• Press and hold the button for 1 second or  
longer to turn off the power.  
• Perform various settings.  
[
] (SOUND) button  
• Switch the operation mode among the radio  
mode, etc.  
• Press the button to enter the sound mode.  
• Press and hold the button for 1 second or  
longer to enter the sound setting mode.  
[OPTION] button  
• Press the button to enter the option mode.  
[ISR] button  
• Recall ISR radio station in memory.  
• Press and hold the button for 1 second or  
longer to enter the adjust mode.  
• Press and hold the button for 2 seconds or  
longer: Store current station into ISR memory  
(radio mode only).  
[SEEK PANEL]  
• The [SEEK PANEL] allows the controls on  
the ends to be moved to right or left to permit  
station tuning (radio), track selection (CD),  
and to perform various settings in the  
adjustment mode.  
[IR RECEIVER]  
• Receiver for remote control unit. (Operating  
range: 30° in all directions)  
[TITLE] button  
• Use the button to switch the user titles or  
track titles, etc. while in the CD/MP3/WMA/  
AAC mode.  
• Press and hold the button to switch the  
display indication (Action display, Title display  
and Clock time display).  
[MENU] button  
• Switch the band, or seek tuning or manual  
tuning while in the radio mode.  
[
] (MUTE) button  
• Turn mute on or off.  
[Q] (EJECT) button  
• Press the button to enter the list search mode  
while in the CD/MP3/WMA/AAC mode.  
• Press to open the MOTORIZED FACE and  
insert a CD into the CD SLOT.  
• Press and hold the button for 1 second or  
longer to play the first track while in the CD/  
MP3/WMA/AAC mode.  
• Press to eject a CD loaded in the unit.  
[VOL] button  
• Push the button upward or downward to  
adjust the volume.  
• Press the button to change the character.  
[
] button  
[CD SLOT]  
• CD insertion slot.  
• Play or pause a track while in the CD/MP3/  
WMA/AAC mode.  
• Press the button to enter the preset memory  
mode (radio).  
• Confirm various settings.  
4
DXZ775USB  
Display Items  
Source indication  
FM1-3, AM : Radio mode  
SR1-3  
XM1-3  
CD  
USB  
iPod  
: Satellite radio mode (SIRIUS)  
: Satellite radio mode (XM)  
: CD/MP3/WMA/AAC mode  
: USB mode  
Radio mode: Preset No. / frequency  
CD mode : Track No. / playback time  
MP3/WMA/AAC mode  
: Folder No. /track No. / playback time  
CD / DVD changer mode  
: Disc No. / track No. / playback time  
TV mode : Preset No. / channel  
: iPod BB mode  
CDC1-4 : CD changer mode  
DVDC1-4 : DVD changer mode  
TV1-2  
AUX  
TEL  
: TV mode  
: AUX mode  
: Telephone mode  
Clock time  
indication  
Operation status indication  
Titles indication  
Source icon  
(3 patterns)  
: Disc/Folder random  
: Disc/Folder repeat  
: Disc/Folder scan  
: Track random  
: Track repeat  
: Track/Preset/Service scan  
: Auto store  
A.RDM  
A.RPT  
A.SCN  
RDM  
RPT  
SCN  
AS  
ST  
: MP3 indication  
: WMA indication  
: Manual indication  
: Category mode indication  
: Channel mode indication  
: Satellite indication  
: Digital Z-Enhancer indication  
: Sound restorer indication  
MP3  
WMA  
MANU  
CAT MODE  
CH MODE  
SAT  
DZE  
SR  
: Stereo indication (radio only)  
LCD Screen  
In extreme cold, the screen movement may slow down and the screen may darken, but this is normal.  
The screen will recover when it returns to normal temperature.  
DXZ775USB  
5
4. DCP  
The control panel can be detached to prevent  
theft. When detaching the control panel, store it  
in the DCP (DETACHABLE CONTROL PANEL)  
case to prevent scratches.  
Attaching the DCP  
1. Insert the DCP so that the Asection on the  
right side of the DCP catches on the hook B  
on the unit.  
We recommend taking the DCP with you when  
leaving the car.  
Removing the DCP  
1. With the MOTORIZED FACE closed, turn off  
the power.  
2. Press the [RELEASE] button deeply to open  
the DCP.  
[RELEASE] button  
2. Press the left side Cof the DCP carefully to  
fit it in place.  
3. Pull the DCP toward you and remove it.  
CAUTION  
• The DCP can easily be damaged by  
shocks. After removing it, be careful not to  
drop it or subject it to strong shocks.  
• If the [RELEASE] button is pressed and  
the DCP is not locked into place, it may fall  
out from vibration of the car. This can  
break the DCP, so after removing it, either  
install it on the unit or put it in its DCP  
case.  
DCP  
CAUTION  
• Always close the MOTORIZED FACE  
before removing the DCP.  
• The connector connecting the unit and the  
DCP is an extremely important part. Be  
careful not to damage it by pressing on it  
with fingernails, screwdrivers, etc.  
• If you remove the DCP with the  
MOTORIZED FACE open, the MOTORIZED  
FACE closes immediately. Be careful not  
to get your fingers caught.  
Note:  
• If the DCP is dirty, wipe off the dirt with a soft, dry  
cloth only.  
6
DXZ775USB  
5. REMOTE CONTROL  
Inserting the Battery  
1Turn over the remote control unit and slide  
the cover in the direction indicated by the  
arrow in the illustration.  
2Insert the battery (CR2025) into the insertion  
guides, with the printed side (+) facing  
upwards.  
3Press the battery in the direction indicated by  
the arrow so that it slides into the  
compartment.  
4Replace the cover and slide in until it clicks  
Insertion guide  
into place.  
Notes:  
Misuse may result in rupture of the battery,  
producing leakage of fluid and resulting in personal  
injury or damage to surrounding materials. Always  
follow these safety precautions:  
R
• Use only the designated battery.  
• When replacing the battery, insert properly, with  
+/– polarities oriented correctly.  
• Do not subject battery to heat, or dispose of in fire  
or water. Do not attempt to disassemble the  
battery.  
• Dispose of used batteries properly.  
DXZ775USB  
7
Functions of Remote Control Unit Buttons  
Some buttons on the remote control unit have different functions from the corresponding buttons on the main  
unit.  
Signal transmitter  
[
]
[
]
SRC  
BND  
[
]
]
[
]
MUTE  
DISP  
[
ISR  
[
[
]
RDM  
]
RPT  
[
]
SCN  
Shared modes  
Radio/Satellite Radio modes  
[SRC] button  
• Press the button to turn on the power.  
[BND] button  
• Switches reception band.  
Press and hold the button for 1 second or  
longer to turn off the power.  
[x], [v] buttons  
• Moves preset channels up and down.  
• Use to alternate operation mode among the  
various modes.  
[SCN] button  
• Press to perform preset scan.  
[w], [z] buttons  
• Press and hold the button for 2 seconds or  
longer to perform auto store.  
• Increases and decreases volume.  
[MUTE] button  
• Turns mute function on and off.  
• In the Satellite Radio mode, press once to  
perform category scan; hold depressed for 1  
second or longer to perform preset scan.  
[ISR] button  
• Recalls ISR radio station stored in memory.  
CD/MP3/WMA/AAC and USB  
• Press and hold the button for 2 seconds or  
longer to store current station in ISR memory  
(radio mode only).  
modes  
[BND] button  
• Press to play the first track.  
[DISP] button  
[x], [v] buttons  
• Press to alternate among action display, title  
display and Clock time display, etc.  
• Press to move the tracks up and down.  
• Press and hold the button for 1 second or  
longer to perform fast-forward/fast-backward.  
8
DXZ775USB  
Functions of Remote Control Unit Buttons  
[
] button  
iPod BB mode  
• Switches between playback and pause.  
[x], [v] buttons  
• Press to move the tracks up and down.  
[SCN] button  
• Press to perform scan play.  
• Press and hold the button for 1 second or  
longer to perform fast-forward/fast-backward.  
• When in MP3/WMA/AAC and USB modes,  
press and hold the button for 1 second or  
longer to perform folder scan play.  
[
] button  
• Switches between playback and pause.  
[RPT] button  
• Press to perform repeat play.  
[RPT] button  
• Press to perform repeat play.  
• When in MP3/WMA/AAC and USB modes,  
press and hold the button for 1 second or  
longer to perform folder repeat play.  
• Press and hold the button for 1 second or  
longer to perform all repeat play.  
[RDM] button  
• Press to perform random play.  
[RDM] button  
• Press to perform random play.  
• Press and hold the button for 1 second or  
longer to perform all random play.  
• When in MP3/WMA/AAC and USB modes,  
press and hold the button for 1 second or  
longer to perform folder random play.  
TV mode  
[BND] button  
• Switches reception band.  
CD changer/DVD changer modes  
[BND] button  
• Press to switch to next disc in ascending  
order.  
[x], [v] buttons  
• Moves preset channels up and down.  
[SCN] button  
• Press to perform preset scan.  
[x], [v] buttons  
• Press to move the tracks up and down.  
• Press and hold the button for 2 seconds or  
longer to perform auto store.  
• Press and hold the button for 1 second or  
longer to perform fast-forward/fast-backward.  
[RDM] button  
• Press to alternate between TV and VTR.  
[
] button  
• Switches between playback and pause.  
[SCN] button  
• Press to perform scan play.  
• Press and hold the button for 1 second or  
longer to perform disc scan play.  
[RPT] button  
• Press to perform repeat play.  
• Press and hold the button for 1 second or  
longer to perform disc repeat play.  
[RDM] button  
• Press to perform random play.  
• Press and hold the button for 1 second or  
longer to perform disc random play.  
DXZ775USB  
9
6. OPERATIONS  
Note:  
• Be sure to read this chapter referring to the front diagrams of chapter “CONTROLS” on page ii (unfold).  
Basic Operations  
2way speaker system (2WAY)  
CAUTION  
Tweeter (left)  
Tweeter (right)  
Be sure to lower the volume before  
Front speaker  
(left)  
Front speaker  
(right)  
switching off the unit power or the ignition  
key. The unit remembers its last volume  
setting. If you switch the power off with the  
volume up, when you switch the power back  
on, the sudden loud volume may hurt your  
hearing and damage the unit.  
Rear speaker  
(left)  
Rear speaker  
(right)  
1. Push the [SEEK PANEL] leftward or  
Selecting speaker system  
When this product is turned on for the first time,  
it allows you to select a speaker system.  
rightward to select the setting.  
Each time you push the [SEEK PANEL]  
leftward or rightward, the setting change in  
the following order:  
Speaker system  
Speaker Speaker configuration  
system  
NORMAL3WAY2WAY↔  
NORMAL”...  
NORMAL Front 2ch Rear 2ch Subwoofer 2ch  
(Normal)  
2. Press the [  
] button.  
3. Push the [SEEK PANEL] leftward or  
3WAY  
(3way)  
High 2ch Mid 2ch  
High 2ch Mid 2ch  
Subwoofer 2ch  
Rear 2ch  
rightward to select “OK” or “CANCEL”.  
4. Press the [  
setting.  
Refer to the section “Adjusting Sound Mode”  
(page 12) and “Adjusting Sound Setting Mode”  
(page 16).  
] button to store the  
2WAY  
(2way)  
Normal speaker system (NORMAL)  
Note:  
• The first time this unit is turned on after the wire  
connections are completed, it must be checked  
what equipment is connected. When the power is  
turned on, “SYSTEM CHECK” appears in the  
display, then the unit returns to the selecting  
speaker system.  
Front speaker  
(left)  
Front speaker  
(right)  
Rear speaker  
(left)  
Rear speaker  
(right)  
System check function  
Subwoofer  
If you change your speaker system while the  
power of this unit is on, perform the System  
check function to select the appropriate speaker  
system again. See “Performing a system  
check” (page 28) for details.  
3way speaker system (3WAY)  
Tweeter (right)  
Tweeter (left)  
Front speaker  
(left)  
Front speaker  
(right)  
CAUTION  
Select the speaker system suited to your  
speaker configuration. Failing to do so can  
damage your speakers.  
Subwoofer  
10  
DXZ775USB  
Basic Operations  
Turning on/off the power  
Switching the display  
Note:  
Press and hold the [TITLE] button for 1 second  
or longer to select the desired display.  
• Be careful about using this unit for a long time  
without running the engine. If you drain the car’s  
battery too far, you may not be able to start the  
engine and this can reduce the service life of the  
battery.  
When the power is turned on  
1. Each time you press and hold the [TITLE]  
button for 1 second or longer, the display  
switches in the following order:  
1. Press the [SRC] button.  
Action display Title display Clock time  
display Action display...  
The mode that was previous active is  
displayed.  
When the power is turned off  
1. Each time you press the [TITLE] button, the  
clock time appears or disappears in the  
display.  
2. Press and hold the [SRC] button for 1  
second or longer to turn off the power for the  
unit.  
Selecting a mode  
1. Press the [SRC] button to change the  
Mute  
Use this function to turn off the sound  
immediately.  
operation mode.  
2. Each time you press the [SRC] button, the  
operation mode changes in the following  
order:  
1. Press the [ ] button.  
The sound turns off and “MUTE” blinks in the  
display.  
Radio (Satellite radio) CD/MP3/WMA/  
AAC USB (iPod BB) (CD changer) ➜  
(DVD changer) (TV) AUX Radio...  
2. Press the [ ] button again to cancel the  
mute mode.  
External equipment not connected with  
CeNET is not displayed.  
Adjusting the volume  
1. Push the [VOL] button upward or downward  
to adjust the volume.  
The volume level is from 0 (minimum) to 33  
(maximum).  
DXZ775USB  
11  
Basic Operations  
Adjusting the subwoofer output  
volume  
Adjusting Sound Mode  
You can adjust the volume output from the unit’s  
subwoofer output terminal.  
To change sound mode  
S-W VOLUME” can be adjusted only when  
SUB WOOFER” is set to “ST” or “MONO”  
(page 19).  
1. Press the [ ] button and select the sound  
mode to adjust.  
2. Push the [SEEK PANEL] leftward or  
rightward to select the “item  
name”.  
2-1. Select the “S-W VOLUME”.  
3-1. Push the [P.CH] button upward or  
downward to change the output volume.  
The factory default setting is “0”.  
(Setting range: +6 to –6)  
Setting the Digital Z-Enhancer  
This unit are provided with 3 types of sound  
tone effects stored in memory. Select the one  
you prefer.  
The factory default setting is “DZE OFF”.  
2-1. Select the “DZE”.  
When speaker system is “NORMAL”:  
S-W VOLUMEDZEP.EQ↔  
BASSTREBLES RESTORER”  
HPFS-W LPFBALANCE↔  
FADER”  
When speaker system is “3WAY”:  
3-1. Press the [  
] button.  
S-W VOLUMEDZEP.EQ↔  
BASSTREBLES RESTORER”  
BALANCE”  
3-2. Push the [SEEK PANEL] leftward or  
rightward to select the tone effect. Each  
time you push the [SEEK PANEL], the tone  
effect changes in the following order:  
When speaker system is “2WAY”:  
DZE OFFDZE 1DZE 2DZE  
3”  
DZEP.EQBASSTREBLE”  
S RESTORERBALANCE↔  
FADER”  
DZE OFF : no sound effect  
3. Push the [P.CH] button upward or  
downward to select the “desired setting  
value”.  
DZE 1  
DZE 2  
: Suitable for genuine speakers  
: Suitable for separate  
speakers  
In the case of item names appearing with  
DZE 3  
: Suitable for co-axial speakers  
the “ENT” suffix after the item name, the  
3-3. When the “DZE 1”, “DZE 2” or “DZE 3” is  
set, push the [P.CH] button upward or  
downward to change the DZE level from +3  
to –3.  
[
] button must be pressed to display  
the setting value.  
P.EQ” can be adjusted only when the  
P.EQ ON/OFF” is set to “ON” (page 19)  
and “EQ SELECT” is set to “P.EQ” (page  
19).  
The factory default setting is “0”.  
BASS” and “TREBLE” can be adjusted  
only when “DZE” is set to “DZE OFF” (page  
12) and “EQ SELECT” is set to “B/T” (page  
19).  
After completing settings, press the [  
button to return to the previous mode.  
]
Note:  
• During sound adjustment mode, if no operation  
is performed for more than 10 seconds, this  
mode can be canceled and return to the  
previous mode.  
12  
DXZ775USB  
Basic Operations  
Compensation  
Setting P.EQ  
There is no need to compensate frequency  
characteristics if they are flat (no peaks or  
valleys) when you have measured the  
frequency characteristics with a measuring  
device. However, sometimes the frequency  
characteristics rise or fall in some places. If this  
happens, the frequency characteristics must be  
compensated. Create a frequency curve having  
characteristics that are opposite to the center  
frequency of parts where the characteristics rise  
and fall to cancel out these peaks and values,  
and make the frequency characteristics as flat  
as possible.  
P.EQ (Parametric Equalizer) allows you to  
compensate the entire frequency level range in  
detail by smooth curve using frequency  
compensation matched to the type of your car.  
The item corresponding to the system set in the  
section “Selecting speaker system” (page 10)  
will be displayed.  
2-1. Select “P.EQ”.  
3-1. Press the [  
] button.  
When speaker system is “NORMAL”:  
3-2. Push the [SEEK PANEL] leftward or  
rightward and select from:  
Making the frequency characteristics as flat as  
possible is called “Compensation”.  
SEDAN-1SEDAN-2MINI VAN-1”  
MINI VAN-2WAGONUSER”...  
On this unit, frequency characteristics can be  
compensated by P.EQ (Parametric Equalizer).  
P.EQ basic menu  
Speaker Mounting  
No. Display name  
Compensation of frequency  
position  
characteristics  
1
2
3
4
5
6
SEDAN-1  
(sedan-1)  
Front: Front door  
Rear: Rear parcel  
The figure below shows the relationship  
between the center frequency, gain and Q  
curve.  
SEDAN-2  
(sedan-2)  
Front: Front door  
Rear: Rear door  
MINI VAN-1  
(mini van-1)  
Front: Front door  
Rear: Luggage (side)  
Level  
(dB)  
Q curve(Q)  
F
f
Q =  
MINI VAN-2  
(mini van-2)  
Front: Front door  
Rear: Rear door  
3dB  
WAGON  
(wagon)  
Front: Front door  
Rear: Luggage (side)  
Gain  
f
USER (user)  
User preference  
3-3. Press the [OPTION] button.  
Frequency  
curve  
Frequency  
(Hz)  
3-4. Press the [MENU] button and select from:  
BAND1BAND2BAND3➜  
BAND1”...  
Center  
Frequency (F)  
3-5. Push the [SEEK PANEL] leftward or  
Q curve  
rightward and select from:  
The Q curve becomes sharper when the  
numerical value is increased, and smoother  
when the numerical value is decreased.  
(Front speaker)  
FRONT  
(Frequency) (20 Hz to 20 kHz)  
• FREQUENCY  
Flat frequency characteristics can be made by  
selecting a Q curve opposite to that of the curve  
to be compensated.  
• GAIN (Gain) (–12 dB to +12 dB)  
• Q  
(Q curve) (1, 3, 5, 7, 20)  
(Rear speaker)  
REAR  
(20 Hz to 20 kHz)  
• FREQUENCY  
(–12 dB to +12 dB)  
• GAIN  
Q curve : 1  
Q curve : 20  
(1, 3, 5, 7, 20)  
Q  
FRONT  
DXZ775USB  
13  
Basic Operations  
P.EQ basic menu setting values  
F: Center frequency, Q: Q curve, G: Gain (output level)  
Parametric Equalizer Parameters (default)  
No. (car type)  
Channel  
F
Band 1  
Band 2  
Q
Band 3  
Q
Q
G
F
G
F
G
1 (SEDAN-1) Front  
Rear  
250 Hz  
250 Hz  
3
–8 dB  
–10 dB  
–10 dB  
+3 dB  
–4 dB  
–6 dB  
–4 dB  
–8 dB  
–8 dB  
–8 dB  
0 dB  
2 kHz  
1
5
3
5
3
3
3
5
3
1
1
1
–4 dB  
0 dB  
5 kHz  
8 kHz  
1
5
1
5
7
5
3
5
1
5
1
1
–4 dB  
0 dB  
–5 dB  
0 dB  
+3 dB  
0 dB  
+3 dB  
0 dB  
–6 dB  
0 dB  
0 dB  
0 dB  
3
7
7
5
1
3
3
3
3
1
1
1.25 kHz  
800 Hz  
125 Hz  
1.25 kHz  
630 Hz  
1.25 kHz  
500 Hz  
1 kHz  
2 (SEDAN-2) Front  
Rear  
250 Hz  
80 Hz  
–4 dB  
–12 dB  
–4 dB  
–4 dB  
–8 dB  
–5 dB  
–8 dB  
–8 dB  
0 dB  
8 kHz  
1.25 kHz  
2 kHz  
3
Front  
Rear  
Front  
Rear  
Front  
Rear  
Front  
Rear  
125 Hz  
250 Hz  
250 Hz  
250 Hz  
250 Hz  
250 Hz  
500 Hz  
500 Hz  
(MINI VAN-1)  
8 kHz  
4
80 Hz  
(MINI VAN-2)  
8 kHz  
5 (WAGON)  
10 kHz  
8 kHz  
800 Hz  
1 kHz  
6 (USER)  
5 kHz  
0 dB  
1 kHz  
0 dB  
5 kHz  
3-6. Push the [P.CH] button upward or  
2WAY mode  
downward to adjust the frequency, the gain  
and the Q.  
LEFT  
(Front speaker (left))  
3-7. Press and hold the [  
] button for 2  
FREQUENCY  
RIGHT  
(Front speaker (right))  
• FREQUENCY  
(Frequency)  
seconds or longer to store the adjusting in  
USER memory and auto return to the  
USER mode.  
• GAIN  
(Gain)  
• Q  
• GAIN  
When speaker system is “3WAY” or  
“2WAY”:  
(Q curve)  
Q  
3-2. Press the [MENU] button and select from:  
LEFT  
BAND1BAND2BAND3➜  
3-4. Push the [P.CH] button upward or  
downward to adjust the frequency, the gain  
and the Q.  
BAND1”...  
3-3. Push the [SEEK PANEL] leftward or  
rightward and select from:  
Items  
Adjustable  
range  
Initial value  
3WAY mode  
LEFT  
FREQUENCY 20 Hz to 20 kHz 500 Hz  
(Frequency)  
(Front speaker (left))  
• FREQUENCY  
RIGHT  
(Front speaker (right))  
• FREQUENCY  
(Frequency)  
GAIN (Gain)  
–12 dB to +12 0 dB  
dB  
• GAIN  
(Gain)  
Q (Q curve)  
1, 3, 5, 7, 20  
1
• Q  
• GAIN  
(Q curve)  
3-5. Press the [  
] button to return to the  
Q  
previous mode.  
LEFT  
Note:  
• Press and hold the [  
] button for 2  
seconds or longer to copy the settings between  
left and right (for 3WAY or 2WAY speaker  
system).  
14  
DXZ775USB  
Basic Operations  
Adjusting the bass  
2-1. Select “BASS”.  
3-1. Press the [  
Adjusting the fader  
FADER” can be adjusted only when the  
speaker system is set to “2WAY” or “NORMAL”.  
] button.  
2-1. Select “FADER”.  
3-2. Push the [P.CH] button upward or  
downward to adjust the gain from –6 to +6  
(The factory default setting is “0”).  
3-1. Push the [P.CH] button upward to  
emphasize the sound from the front  
speaker, push the button downward to  
emphasize the sound from the rear  
speaker.  
3-3. Press the [  
previous mode.  
] button to return to the  
Adjusting the treble  
2-1. Select “TREBLE”.  
The factory default setting is “0”.  
(Adjustment range: R12 to F12)  
3-1. Press the [  
] button.  
Setting high pass filter  
HPF” can be adjusted only when the speaker  
system is set to “NORMAL”.  
3-2. Push the [P.CH] button upward or  
downward to adjust the gain from –6 to +6  
(The factory default setting is “0”).  
2-1. Select “HPF”.  
3-3. Press the [  
previous mode.  
] button to return to the  
3-1. Push the [P.CH] button upward or  
downward to select the setting. Each time  
you push the [P.CH] button, the setting  
changes in the following order:  
Adjusting the sound restorer  
The sound restorer enriches the playback of all  
types of music files that have undergone any  
level of data compression.  
THRGH50Hz80Hz125Hz”  
The factory default setting is “THRGH”  
(through).  
2-1. Select “S RESTORER”.  
3-1. Push the [P.CH] button upward or  
Setting low pass filter  
S-W LPF” can be adjusted only when the  
downward to adjust.  
Each time you push the [P.CH] button, the  
sound restorer changes in the following  
order:  
speaker system is set to “NORMAL” .  
If subwoofer function is set to “ST” or “MONO”,  
S-W LPF” can be selected.  
OFF123”  
2-1. Select “S-W LPF”.  
The factory default setting is “OFF”.\  
3-1. Push the [P.CH] button upward or  
Set this adjustment in accordance with the  
music source used  
downward to select the setting.  
Each time you push the [P.CH] button, the  
OFF: For music sources compressed at  
setting changes in the following order:  
high bit rate  
THRGH50Hz80Hz125Hz”  
1: For music sources compressed for high  
quality at low bit rate  
The factory default setting is “THRGH”  
(through).  
2: For music sources compressed for  
standard quality at low bit rate  
3: For music sources compressed for low  
quality at low bit rate  
Adjusting the balance  
2-1. Select “BALANCE”.  
3-1. Push the [P.CH] button upward to  
emphasize the sound from the right  
speaker, push the button downward to  
emphasize the sound from the left speaker.  
The factory default setting is “0”.  
(Adjustment range: L12 to R12)  
DXZ775USB  
15  
Basic Operations  
2-1. Select “PRESET”.  
Adjusting Sound Setting  
Mode  
3-1. Press the [  
] button.  
3-2. Push the [SEEK PANEL] leftward or  
rightward and select from:  
LOADSAVEINITIAL↔  
LOAD”...  
To change sound setting mode  
1. Press and hold the [ ] button for 2  
3-3. Push the [P.CH] button upward or  
seconds or longer and select the sound  
setting mode to adjust.  
downward to adjust the load and the save.  
LOAD : “SELECTING 1” to “SELECTING  
3” (The factory default setting is  
SELECTING 1”)  
2. Push the [SEEK PANEL] leftward or  
rightward to select the “item name”.  
When speaker system is “NORMAL”:  
SAVE : “1” to “3” (The factory default  
setting is “1”)  
PRESETALL SEATT  
ALIGNMENTP.EQ ON/OFFEQ  
SELECTSUB WOOFER↔  
PRESET”...  
3-4. Press and hold the [  
store into memory.  
] button to  
(LOAD: Press and hold the button for 1  
second or longer.  
When speaker system is “3WAY”:  
PRESETALL SEATX-OVER”  
T ALIGNMENTSPEAKER GAIN”  
P.EQ ON/OFFEQ SELECT↔  
SUB WOOFERPRESET”...  
SAVE: Press and hold the button for 2  
seconds or longer.)  
Setting the all seat  
The setting of “T ALIGNMENT” and “SPEAKER  
GAIN” temporarily returns to the factory default  
setting. When the setting that is adjusted for the  
driver's seat returns to the factory default  
setting, a sound suitable for all seats is  
provided.  
When speaker system is “2WAY”:  
PRESETALL SEATX-OVER”  
T ALIGNMENTSPEAKER GAIN”  
P.EQ ON/OFFEQ SELECT↔  
PRESET”...  
In the case of item names appearing with  
The factory default setting is “OFF”.  
2-1. Select “ALL SEAT”.  
the “ENT” suffix, after the item name, the  
[
] button must be pressed to display  
3-1. Push the [P.CH] button upward or  
the setting value.  
downward to select “ON” or “OFF”.  
After completing settings, press the [  
button to return to the previous mode.  
]
Setting the preset setting  
This function allows you to recall, save or  
initialize the sound settings.  
If your speaker system is “3WAY” or “2WAY”,  
you can store and recall up to three adjustments  
you have made to “P.EQ ON/OFF”, “X-OVER”,  
T ALIGNMENT”, “SPEAKER GAIN”.  
LOAD: To recall the stored sound settings.  
SAVE: To save the sound settings.  
INITIAL: To initialize the sound settings.  
The load and the save can be adjusted as  
follows.  
16  
DXZ775USB  
Basic Operations  
HIGH  
Setting the X-OVER  
This function allows you to adjust the speaker  
setting such as cutoff frequencies or slope  
matched to the speakers you are using.  
(Crossover).  
Items  
Adjustable  
range  
Initial value  
HPF  
THRGH  
(through), 25  
Hz to 20 kHz  
2 kHz  
2-1. Select “X-OVER”.  
3-1. Press the [  
] button.  
HPF SLOPE  
PHASE  
–6 dB, –12 dB, –12 dB  
–18 dB  
3-2. Push the [SEEK PANEL] leftward or  
rightward and select from:  
NOR (normal), NOR (normal)  
REV (reverse)  
3WAY mode  
HIGH  
(Front speaker (high))  
• HPF  
(High pass filter)  
MID  
Items  
Adjustable  
range  
Initial value  
• PHASE  
SUB-W  
(Subwoofer)  
• LPF  
LPF  
630 Hz to 10  
kHz, THRGH  
(through)  
2 kHz  
• HPF SLOPE  
(HPF slope)  
• PHASE  
(Phase)  
LPF SLOPE  
HPF  
LPF SLOPE  
HPF  
–6 dB, –12 dB, –12 dB  
–18 dB  
MID  
(Front speaker (mid))  
THRGH  
(through), 25  
Hz to 10 kHz  
THRGH  
(through)  
• LPF  
• HPF SLOPE  
PHASE  
(Low pass filter)  
• LPF SLOPE  
(LPF slope)  
HPF SLOPE  
PHASE  
–6 dB, –12 dB, –12 dB  
–18 dB  
HIGH  
HPF  
• HPF SLOPE  
NOR (normal), NOR (normal)  
REV (reverse)  
2WAY mode  
SUB-W (3WAY)/REAR (2WAY)  
HIGH  
Items  
Adjustable  
range  
Initial value  
(Front speaker (high))  
• HPF  
(High pass filter)  
• PHASE  
LPF  
25 Hz to 10  
kHz, THRGH  
(through)  
80 Hz  
REAR  
(Rear speaker)  
• LPF  
• HPF SLOPE  
(HPF slope)  
• PHASE  
(Phase)  
LPF SLOPE  
HPF  
–6 dB, –12 dB, –12 dB  
–18 dB  
LPF SLOPE  
HPF  
MID  
(Front speaker (mid))  
THRGH  
(through), 16  
Hz to 250 Hz  
THRGH  
(through)  
• LPF  
• HPF SLOPE  
PHASE  
(Low pass filter)  
• LPF SLOPE  
HPF SLOPE  
PHASE  
–6 dB, –12 dB, –12 dB  
–18 dB  
(LPF slope)  
HIGH  
HPF  
NOR (normal), NOR (normal)  
REV (reverse)  
• HPF SLOPE  
3-4. Press the [  
memory.  
] button to store into  
3-3. Push the [P.CH] button upward or  
downward to adjust the “HPF”, “HPF  
SLOPE”, “PHASE”, “LPF” and “LPF  
SLOPE”.  
DXZ775USB  
17  
Basic Operations  
3-3. Push the [P.CH] button upward or  
downward to adjust “HIGH L SP”, “HIGH R  
SP”, “MID L SP”, “MID R SP”, “SUB-W L  
SP”, “SUB-W R SP”, “REAR L SP”, “REAR  
R SP”, “FRONT L SP” and “FRONT R SP”.  
Setting the time alignment  
The distance from the listener up to each  
speaker can be entered in 2.3 cm steps, and the  
time that the sound reaches the listener from  
each speaker can be adjusted (Time alignment).  
Above 12 adjustment item's adjustable  
range: 0 to 501.4 cm (The factory default  
setting is “0”)  
2-1. Select “T ALIGNMENT”.  
3-1. Press the [  
] button.  
3-2. Push the [SEEK PANEL] leftward or  
3-4. Press the [  
previous mode.  
] button to return to the  
rightward and select from:  
3WAY mode  
Setting the speaker gain  
HIGH  
This function allows you to adjust the speaker  
output level. Adjust so that the volumes that are  
output from each speaker are well-balanced  
(Speaker gain).  
(Front speaker (high))  
• HIGH L SP  
SUB-W  
(Subwoofer)  
(Left)  
• SUB-W L SP  
• HIGH R SP  
(Left)  
(Right)  
2-1. Select “SPEAKER GAIN”.  
SUB-W R SP  
MID  
3-1. Press the [  
] button.  
(Right)  
(Front speaker (mid))  
• MID L SP  
3-2. Push the [SEEK PANEL] leftward or  
HIGH  
(Left)  
rightward and select from:  
• MID R SP  
(Right)  
3WAY mode  
HIGH  
(Front speaker (high))  
2WAY mode  
• HIGH L SP  
MID R SP  
HIGH  
(Left)  
(Front speaker (high))  
SUB-W  
• HIGH R SP  
• HIGH L SP  
REAR  
(Rear speaker)  
(Subwoofer)  
(Right)  
(Left)  
• SUB-W L SP  
MID  
(Front speaker (mid))  
• MID L SP  
• REAR L SP  
• HIGH R SP  
(Right)  
(Left)  
SUB-W R SP  
REAE R SP  
MID  
(Front speaker (mid))  
HIGH  
(Right)  
• MID L SP  
HIGH  
(Left)  
2WAY mode  
• MID R SP  
HIGH  
(Front speaker (high))  
(Right)  
• HIGH L SP  
MID R SP  
(Left)  
(Right)  
NORMAL mode  
FRONT  
(Front speaker)  
REAR  
(Rear speaker)  
• HIGH R SP  
(Right)  
• REAR L SP  
MID  
(Front speaker (mid))  
(Left)  
• FRONT L SP  
SUB-W  
(Left)  
(Subwoofer)  
REAR R SP  
• MID L SP  
(Right)  
• SUB-W L SP  
• FRONT R SP  
(Left)  
HIGH  
(Left)  
(Right)  
SUB-W R SP  
REAR  
3-3. Push the [P.CH] button upward or  
downward to adjust the “HIGH L SP”,  
HIGH R SP”, “MID L SP”, “MID R SP”,  
SUB-W L SP”, “SUB-W R SP”, “REAR L  
SP” and “REAR R SP”.  
(Rear speaker)  
(Right)  
• REAR L SP  
FRONT  
(Left)  
• REAR R SP  
(Right)  
Above 10 adjustment item's adjustable  
range: –20 dB to 0 (The factory default  
setting is “0”)  
3-4. Press the [  
previous mode.  
] button to return to the  
18  
DXZ775USB  
Basic Operations  
Setting the P.EQ ON/OFF  
The factory default setting is “OFF”.  
2-1. Select “P.EQ ON/OFF”.  
3-1. Push the [P.CH] button upward or  
downward to select “ON” or “OFF”.  
Setting the EQ SELECT  
You can change the equalizer that adjusts the  
sound quality.  
The factory default setting is “P.EQ”.  
2-1. Select “EQ SELECT”.  
3-1. Push the [P.CH] button upward or  
downward to select “P.EQ” or “B/T” (Bass/  
Treble).  
Setting the Subwoofer  
The factory default setting is “OFF”.  
2-1. Select “SUB WOOFER”.  
3-1. Push the [P.CH] button upward or  
downward to select “ST”, “MONO” or  
OFF”.  
DXZ775USB  
19  
Radio Operations  
Quick tuning  
Listening to the radio  
Push the [SEEK PANEL] leftward or rightward  
and hold in position for 1 second or longer to  
tune in a station.  
1. Press the [SRC] button and select the radio  
mode. The frequency appears in the display.  
2. Press the [MENU] button and select the  
radio band. Each time the button is pressed,  
the radio reception band changes in the  
following order:  
Step tuning  
Push the [SEEK PANEL] leftward or rightward  
to manually tune in a station.  
FM1 FM2 FM3 AM FM1...  
Recalling a preset station  
3. Push the [SEEK PANEL] leftward or  
rightward to tune in the desired station.  
A total of 24 preset positions (6-FM1, 6-FM2, 6-  
FM3, 6-AM) exists to store individual radio  
stations in memory. Pushing the [P.CH] button  
upward or downward recalls the stored radio  
frequency automatically.  
Tuning  
There are 3 types of tuning mode available,  
seek tuning, manual tuning and preset tuning.  
1. Press the [MENU] button and select the  
desired band (FM or AM).  
Seek tuning  
1. Press the [MENU] button and select the  
2. Push the [P.CH] button upward or downward  
to recall the stored station.  
desired band (FM or AM).  
2. Tune into a station.  
Manual memory  
1. Select the desired station with seek tuning or  
If “MANU” is lit in the display, press and hold  
the [MENU] button for 1 second or longer.  
MANU” in the display goes off and seek  
tuning is now available.  
manual tuning.  
2. Press the [  
] button to enter the  
preset memory mode.  
When the [SEEK PANEL] is pushed rightward,  
the station is sought in the direction of higher  
frequencies; if the [SEEK PANEL] is pushed  
leftward, the station is sought in the direction of  
lower frequencies.  
3. Push the [P.CH] button upward or downward  
to select a desired station, then press and  
hold the [  
] button for 2 seconds or  
longer to store the current station into preset  
memory.  
Manual tuning  
There are 2 ways available: Quick tuning and  
step tuning.  
When you are in the step tuning mode, the  
frequency changes one step at a time. In the  
quick tuning mode, you can quickly tune the  
desired frequency.  
1. Press the [MENU] button and select the  
desired band (FM or AM).  
If “MANU” is not lit in the display, press and  
hold the [MENU] button for 1 second or  
longer. “MANU” is lit in the display and manual  
tuning is now available.  
2. Tune into a station.  
20  
DXZ775USB  
Radio Operations  
Auto store  
Instant station recall (ISR)  
Auto store is a function for storing up to 6  
stations that are automatically tuned in  
sequentially. If 6 receivable stations cannot be  
received, a previously stored station remains  
unoverwritten at the memory position.  
Instant station recall is a special radio preset  
that instantly accesses a favorite radio station at  
a touch of a button. The ISR function even  
operates with the unit in other modes.  
ISR memory  
1. Press the [MENU] button and select the  
1. Select the station that you wish to store in  
ISR memory.  
desired band (FM or AM).  
2. Press the [OPTION] button.  
2. Press and hold the [ISR] button for 2  
seconds or longer.  
3. Push the [SEEK PANEL] leftward or  
rightward to select “AUTO STORE”.  
Recalling a station with ISR  
4. Press and hold the [  
] button for 2  
In any mode, press the [ISR] button to turn on  
the radio function and tune the selected radio  
station. “ISR” appears in the display. Press the  
[ISR] button again to return to the previous  
mode.  
seconds or longer. The stations with good  
reception are stored automatically to the  
preset channels.  
Preset scan  
Preset scan receives the stations stored in  
preset memory in order. This function is useful  
when searching for a desired station in memory.  
1. Press the [OPTION] button.  
2. Push the [SEEK PANEL] leftward or  
rightward to select “PRESET SCN”.  
3. Press the [  
When a desired station is tuned in, press the  
] button again to continue receiving  
that station.  
] button.  
[
DXZ775USB  
21  
CD/MP3/WMA/AAC Operations  
• Tracks purchased at an iTunes Music store,  
and copyright-protected files cannot be  
played.  
MP3/WMA/AAC  
What is MP3?  
• When playing AAC files that include image  
data, additional time may be required before  
playback begins.  
MP3 is an audio compression method and  
classified into audio layer 3 of MPEG standards.  
This audio compression method has penetrated  
into PC users and become a standard format.  
• Files may not play properly, depending on the  
iTunes version under which an AAC file is  
encoded.  
This MP3 features the original audio data  
compression to about 10 percent of its initial  
size with a high sound quality. This means that  
about 10 music CDs can be recorded on a CD-  
R disc or CD-RW disc to allow a long listening  
time without having to change CDs.  
Precautions when creating MP3/  
WMA/AAC disc  
Usable sampling rates and bit rates  
1. MP3: Sampling rate 8 kHz–48 kHz,  
Bit rate 8 kbps–320 kbps / VBR  
2. WMA: Bit rate 32 kbps–192 kbps  
3. AAC: Sampling rate 8 kHz–48 kHz,  
Bit rate 8 kbps–320 kbps / VBR  
What is WMA?  
WMA is the abbreviation of Windows Media  
Audio, an audio file format developed by  
Microsoft Corporation.  
Notes:  
File extensions  
• If you play a file with DRM (Digital Rights  
Management) for WMA remaining ON, no audio  
is output (The WMA indicator blinks).  
• Windows Media™, and the Windows ® logo are  
trademarks, or registered trademarks of Microsoft  
Corporation in the United States and/or other  
countries.  
1. Always add a file extension “.MP3” (.mp3),  
.WMA” (.wma) or “.M4A” (.m4a) to MP3,  
WMA or AAC file by using single byte letters.  
If you add a file extension other than  
specified or forget to add the file extension,  
the file cannot be played.  
To disable DRM (Digital Rights  
Management)  
2. Files without MP3/WMA/AAC data will not  
play. The indication “– –:– –” appears in the  
play time display if you attempt to play files  
without MP3/WMA/AAC data.  
1. When using Windows Media Player 8, click  
on TOOLS OPTIONS COPY MUSIC  
tab, then under COPY SETTINGS, unclick  
the check box for PROTECT CONTENT.  
Then, reconstruct files.  
Logical format (File system)  
1. When writing MP3/WMA/AAC file on a CD-R  
disc or CD-RW disc, please select “ISO9660  
level 1, 2 or JOLIET or Romeo or APPLE  
ISO” as the writing software format. Normal  
play may not be possible if the disc is  
recorded on another format.  
2. When using Windows Media Player 9, click  
on TOOL OPTIONS MUSIC RECORD  
tab, then under Recording settings, unclick  
the Check box for RECORD PROTECTED  
MUSIC. Then, reconstruct files.  
2. The folder name and file name can be  
displayed as the title during MP3/WMA/AAC  
play but the title must be within 64 single  
byte alphabetical letters and numerals  
(including an extension).  
Personally constructed WMA files are used  
at your own responsibility.  
What is AAC?  
• AAC is an acronym for “Advanced Audio  
Coding” and refers to the audio compression  
method used with video compression  
standards MPEG-2 and MPEG-4.  
3. Do not affix a name to a file inside a folder  
having the same name.  
Folder structure  
1. A disc with a folder having more than 8  
hierarchical levels will be impossible.  
• AAC files composed with the following  
conditions can be played:  
- AAC files encoded with iTunes.  
- iTunes Ver. 7.0 or earlier.  
- File extension “.m4a” (“.M4A”)  
22  
DXZ775USB  
CD/MP3/WMA/AAC Operations  
Number of files or folders  
1. Up to 255 files can be recognized per folder.  
Up to 510 files can be played.  
Backup Eject function  
You can eject a disc by pressing the [Q] button  
even if the engine key or ACC is at the OFF  
position.  
2. Tracks are played in the order that they were  
recorded onto a disc. (Tracks might not  
always be played in the order displayed on  
the PC.)  
CAUTION  
When the disc is ejected, press the [Q]  
button to close the control panel. If the  
control panel is left open, you will hear a  
double beep, and the control panel  
automatically closes.  
3. Some noise may occur depending on the  
type of encoder software used while  
recording.  
Set the type of file to be played  
(multi-session function)  
1. Press the [Q] button.  
The control panel opens.  
When a single disc holds both normal CD type  
tracks and MP3/WMA/AAC type tracks, use this  
command to select which type of track to play.  
2. Press the [Q] button.  
The disc is ejected.  
Note:  
Default setting is “CD”.  
• Always close the MOTORIZED FACE after  
opening it or ejecting the CD.  
• When only one type of track (either music CD  
or MP3/WMA/AAC) is recorded on a disc,  
selecting either type will allow playback of the  
disc.  
CAUTION  
• Be careful not to catch your hand or  
fingers while closing the MOTORIZED  
FACE.  
• When playing CCCD (copy-control CDs), set  
to CD type.  
1. Press the [OPTION] button.  
• Do not try to put your hand or fingers in  
the disc insertion slot. Also never insert  
foreign objects into the slot.  
2. Push the [SEEK PANEL] leftward or  
rightward to select “MULTI SESS”.  
3. Push the [P.CH] button upward or downward  
to select “CD” or “MP3”. The mixed mode is  
switched between CD type or MP3/WMA/  
AAC type.  
• Do not insert discs where adhesive comes  
out from cellophane tape or a rental CD  
label, or discs with marks where  
cellophane tape or rental CD labels were  
removed. It may be impossible to extract  
these discs from the unit and they may  
cause the unit to break down.  
• CD  
When playing music CD only.  
• MP3  
When playing music MP3/WMA/AAC only.  
Listening to a disc already loaded  
in the unit  
4. When setting is completed, remove the disc  
and reinsert it.  
Press the [SRC] button to select the CD/MP3/  
WMA/AAC mode.  
Disc-In-Play function  
When the unit enters the CD/MP3/WMA/AAC  
mode, play starts automatically.  
As long as the ignition key is turned to the ON or  
ACC position, this function allows you to turn the  
power to the unit and start playing the disc  
automatically when the disc is inserted even if  
the power is not turned on.  
If there is no disc loaded, the indication “NO  
DISC” appears in the title display.  
DXZ775USB  
23  
CD/MP3/WMA/AAC Operations  
Loading a CD  
• If MP3/WMA/AAC disc is not input TAG, “NO  
TITLE” appears in the display.  
1. Press the [Q] button. The MOTORIZED  
• For MP3, supports ID3 Tags V2.3 / 2.2 / 1.1 / 1.0.  
• Tag displays give priority to V2.3 / 2.2.  
• In the case of album Tags for WMA, the  
information written into the extension header is  
displayed.  
FACE opens.  
2. Insert a CD into the center of the CD SLOT  
with the labeled side facing up. The CD plays  
automatically after loading.  
Notes:  
• Only ASCII characters can be displayed in Tags.  
• Never insert foreign objects into the CD SLOT.  
• If the CD is not inserted easily, there may be  
another CD in the mechanism or the unit may  
require service.  
Selecting a track  
Track-up  
1. Push the [SEEK PANEL] rightward to move  
ahead to the beginning of the next track.  
• Discs not bearing the  
CD-ROMs cannot be played by this unit.  
or  
mark and  
• Some CDs recorded in CD-R/CD-RW mode may  
not be usable.  
2. Each time you push the [SEEK PANEL]  
rightward, the track advances ahead to the  
beginning of the next track.  
Pausing play  
1. Press the [  
Track-down  
1. Push the [SEEK PANEL] leftward to move  
back to the beginning of the current track.  
] button to pause play.  
PAUSE” appears in the display.  
2. Push the [SEEK PANEL] leftward twice to  
move back to the beginning of the previous  
track.  
2. To resume CD play, press the [  
button again.  
]
Displaying CD titles  
This unit can display title data for CD-text/MP3/  
WMA/AAC disc and user titles input with this  
unit.  
Fast-forward/fast-backward  
Fast-forward  
1. Push the [SEEK PANEL] rightward and hold  
in position for 1 second or longer.  
1. Each time you press the [TITLE] button, the  
Fast-backward  
title display changes in the following order:  
1. Push the [SEEK PANEL] leftward and hold  
in position for 1 second or longer.  
CD-TEXT disc  
Title scan User title (disc) CD-text title  
(track) CD-text title (disc) Artist name ➜  
Title scan ...  
For MP3/WMA/AAC discs, it takes some time  
until the start of searching and between  
tracks. In addition, the playing time may have  
a margin of error.  
MP3/WMA/AAC disc  
Title scan Track Folder Title TAG ➜  
Album TAG Artist TAG Title scan ...  
Folder Select  
This function allows you to select a folder  
containing MP3/WMA/AAC files and start  
playing from the first track in the folder.  
TITLE SCAN  
When the display is changed to the title scan  
mode, all titles of the track scroll automatically.  
When “AUTO SCROLL” is set “ON”, the titles  
scan automatically. When “AUTO SCROLL” is  
set “OFF”, the titles only scan one time. (The  
factory default setting is “ON”. Refer to the  
subsection “Setting the method for title scroll”  
in section “Operations Common to Each  
Mode”.)  
1. Push the [P.CH] button upward or  
downward.  
Push the [P.CH] button upward to move the  
next folder. Push the [P.CH] button  
downward to move the previous folder.  
Folder without an MP3/WMA/AAC file is not  
selectable.  
Notes:  
2. To select a track, push the [SEEK PANEL]  
• If the CD playing is not a CD-text CD or no user  
title has been input, “ uNO TITLE” appears in  
the display.  
leftward or rightward.  
24  
DXZ775USB  
CD/MP3/WMA/AAC Operations  
Top function  
The top function resets the CD player to the first  
track of the disc. Press and hold the [MENU]  
button for 1 second or longer to play the first  
track (track No. 1) on the disc.  
3. Push the [P.CH] button upward or downward  
to select “ALL”, and then press the  
[
] button to perform folder scan play.  
FOLDER SCN” appears in the display.  
Folder scan play starts from the next folder  
after the folder currently being played.  
In case of MP3/WMA/AAC, the first track of a  
folder being played will be returned.  
Repeat play  
This function allows you to play the current track  
repeatedly.  
List search function  
1. Press the [MENU] button to enter the list  
search mode. And then the track list appears  
in the display.  
2. Push the [SEEK PANEL] leftward or  
rightward to select “RPT”.  
3. Push the [P.CH] button upward or downward  
to select “ ”, and then press the [  
button to perform repeat play.  
]
2. Push the [P.CH] button upward or downward  
to select a track.  
TRACK RPT” appears in the display.  
Folder repeat play  
This function allows you to play a track currently  
being played in the MP3/WMA/AAC folder  
repeatedly.  
If you push the [SEEK PANEL] leftward or  
rightward, the track list scrolls 5 lines at a  
time.  
3. Press the [  
] button to play.  
In case of MP3/WMA/AAC, this function is  
performed in the current folder.  
Note:  
2. Push the [SEEK PANEL] leftward or  
rightward to select “RPT”.  
• If no operation is performed for more than 10  
seconds, this mode can be cancel and return to  
the usual mode.  
3. Push the [P.CH] button upward or downward  
to select “ALL”, and then press the  
[
] button to perform folder repeat  
play. “FOLDER RPT” appears in the display.  
Other various play functions  
1. Press the [OPTION] button.  
Random play  
This function allows you to play all tracks  
recorded on a disc in a random order.  
2. Push the [SEEK PANEL] leftward or  
rightward to select “RDM”.  
3. Push the [P.CH] button upward or downward  
Scan play  
to select “ ”, and then press the [  
button to perform random play.  
]
This function allows you to locate and play the  
first 10 seconds of all the tracks recorded on a  
disc.  
TRACK RDM” appears in the display.  
Folder random play  
2. Push the [SEEK PANEL] leftward or  
This function allows you to play all the tracks of  
all the folders recorded on an MP3/WMA/AAC  
disc in a random order.  
rightward to select “SCN”.  
3. Push the [P.CH] button upward or downward  
to select “ ”, and then press the [  
button to perform scan play.  
]
2. Push the [SEEK PANEL] leftward or  
rightward to select “RDM”.  
TRACK SCN” appears in the display.  
Scan play starts from the next track after the  
track currently being played.  
3. Push the [P.CH] button upward or downward  
to select “ALL”, and then press the  
[
] button to perform folder random  
Folder scan play  
This function allows you to locate and play the  
first 10 seconds of the first track of all the folders  
on an MP3/WMA/AAC disc.  
play. “FOLDER RDM” appears in the  
display.  
To cancel the trick play  
2. Push the [SEEK PANEL] leftward or  
2. Push the [SEEK PANEL] leftward or  
rightward to select “TRICK OFF”.  
rightward to select “SCN”.  
3. Press the [  
trick play.  
] button to cancel the  
DXZ775USB  
25  
Operations Common to Each Mode  
COLOR SCANIndigo BlueSurf  
To change adjustment setting  
BlueSilky WhiteAqua Green↔  
Fresh GreenLeaf GreenWarm  
AmberPassion RedVivid Pink”  
Pale PinkDark VioletPure  
PurpleUSER COLOR 1USER  
COLOR 2USER COLOR 3↔  
COLOR SCAN” ...  
1. Press and hold the [OPTION] button for 1  
second or longer to switch to the  
adjustment selection display.  
2. Push the [SEEK PANEL] leftward or  
rightward to select the “item name”.  
CLOCK EDITCOLOR↔  
CONTRASTSCREEN SAVER↔  
MSG INPUTAUTO SCROLL↔  
SCROLL SPEEDDIMMER↔  
BLINK LEDAMP CANCEL↔  
TEL-SPEAKERTEL-SWITCH↔  
SYSTEM CHECK”  
• Setting COLOR SCAN mode  
As selecting “COLOR SCAN”, the color  
automatically changes.  
The factory default setting is “COLOR SCAN”.  
After 3 seconds the color changes to the other.  
• Setting USER mode  
The factory default setting is “RED 8” (red),  
GREEN 8” (green), “BLUE 8” (blue).  
3. Push the [P.CH] button upward or  
downward to select the “desired setting  
value”.  
As selecting “USER COLOR 1, 2, 3”, press the  
[OPTION] button to enter the setting.  
In the case of display appearing “ENT”, the  
[
] button must be pressed to display  
1. Push the [SEEK PANEL] leftward or  
rightward to select “RED”, “GREEN” or  
BLUE”.  
the setting value.  
After completing settings, press the  
[OPTION] button to return to the previous  
mode.  
2. Push the [P.CH] button upward or downward  
to select from 0 to 8.  
3. Press and hold the [  
] button for 2  
Setting the clock  
2-1. Select “CLOCK EDIT”.  
seconds or longer to store the color in  
memory and return to the previous mode.  
3-1. Press the [  
] button  
COLOR  
RED  
(red)  
GREEN BLUE  
(green) (blue)  
3-2. Push the [SEEK PANEL] leftward or  
rightward to select the hour or the minute.  
Indigo Blue  
0
0
8
0
0
3
8
8
8
8
3
6
8
8
8
0
4
8
8
8
8
3
0
0
2
0
0
8
8
8
8
8
7
2
0
0
0
0
3
3
8
8
8
8
8
3-3. Push the [P.CH] button upward or  
Surf Blue  
downward to set the correct time.  
The clock is displayed in 12-hour format.  
Silky White  
Aqua Green  
Fresh Green  
Leaf Green  
3-4. Press the [  
time into memory.  
Note:  
• You cannot set the clock when it is displayed with  
only the ignition on. If you drain or remove the  
car’s battery or take out this unit, the clock is  
reset. While setting the clock, if another button or  
operation is selected, the clock set mode is  
canceled.  
] button to store the  
Warm Amber  
Passion Red  
Vivid Pink  
Pale Pink  
Dark Violet  
Setting the button illumination  
2-1. Select “COLOR”.  
Pure Purple  
USER COLOR 1  
USER COLOR 2  
USER COLOR 3  
3-1. Press the [  
] button.  
3-2. Push the [SEEK PANEL] leftward or  
rightward to select the color type in the  
following orders:  
26  
DXZ775USB  
Operations Common to Each Mode  
3-4 Press the [MENU] button to select a  
character type. Each time you press the  
[MENU] button, the character type changes  
in the following order:  
Setting the contrast  
You can adjust the display contrast to match the  
angle of installation of the unit.  
The factory default setting is “8”. (Adjustment  
level: 1 to 16)  
Capital letters Small letters Numbers/  
Symbols Umlaut Capital letters…  
2-1. Select “CONTRAST”.  
3-5. Push the [P.CH] button upward or  
3-1. Push the [P.CH] button upward or  
downward to select the desired character.  
downward to adjust the contrast.  
3-6. Repeat step 3-3 to 3-5 to enter up to 30  
characters for message.  
Turning the screen saver function on  
or off  
3-7. Press and hold the [  
] button for 2  
This unit is provided with the screen saver  
function which allows you to show various kinds  
of patterns and characters in the operation  
status indication area of the display in a random  
order. You can turn on or off this function. If the  
button operation is performed with the screen  
saver function on, the operation display  
corresponding to the button operation is shown  
for about 30 seconds and the display returns to  
the screen saver display.  
seconds or longer to store the message in  
memory and cancel the input message  
mode.  
Press and hold the [MENU] button for 1  
second or longer to cancel the input  
message. Then press and hold the  
[
] button for 2 seconds or longer to  
store the message and the message return  
to the default setting.  
Setting the method for title scroll  
Set how to scroll in CD-TEXT, MP3/WMA/AAC  
title.  
The factory default setting is “ON”.  
2-1. Select “AUTO SCROLL”.  
The factory default setting is Pattern  
RANDOM”.  
2-1. Select “SCREEN SAVER”.  
3-1. Press the [  
] button.  
3-2. Push the [P.CH] button upward or  
3-1. Push the [P.CH] button upward or  
downward to select the setting.  
downward to select “ON” or “OFF”.  
Pattern RANDOMPattern  
MESSAGEPattern SSPattern  
OFF”  
• ON:  
To scroll automatically.  
• OFF:  
To scroll just 1 time.  
Entering message information  
Message up to 30 characters long can be stored  
in memory and displayed as a type of screen  
saver setting.  
The factory default setting is “Welcome to  
Clarion”.  
Setting the speed of the title scroll  
This function allows you to adjust the speed of  
the title scroll.  
The factory default setting is “3”.  
2-1. Select “MSG INPUT”.  
2-1. Select “SCROLL SPEED”.  
3-1. Press the [  
] button.  
3-1. Push the [P.CH] button upward or  
downward to select from “1” to “6”.  
3-2. Press and hold the [MENU] button for 1  
second or longer to clear the old message.  
3-3. Push the [SEEK PANEL] leftward or  
rightward to move the cursor.  
DXZ775USB  
27  
Operations Common to Each Mode  
Setting the dimmer control  
You can set the dimmer control “HIGH”, “MID”,  
LOW” or “OFF”.  
Cellular phone interrupt setting  
If you connect this unit and your cellular phone  
with a separately sold cable, you can listen to  
your telephone calls on your car speakers.  
The factory default setting is “MID”.  
When the AUX input cable is used to connect a  
AUX BLUETOOTH BB (BLT370) (sold  
separately).  
The factory default setting is “OFF”.  
2-1. Select “TEL-SWITCH”.  
2-1. Select “DIMMER”.  
3-1. Push the [P.CH] button upward or  
downward to select the setting.  
HIGHMIDLOWOFF”  
Anti-theft indicator  
3-1. Push the [P.CH] button upward or  
downward to select the setting in the  
following order:  
The red Anti-theft indicator is a function for  
preventing theft. When the DCP is removed  
from the unit, this indicator blinks.  
The factory default setting is “OFF”.  
2-1. Select “BLINK LED”.  
OFFONMUTE”  
• OFF:  
This unit continues normal operation even  
when the cellular phone is used.  
3-1. Push the [P.CH] button upward or  
downward to select “ON” or “OFF”.  
• ON:  
Setting the external amplifier  
The factory default setting is “OFF”.  
2-1. Select “AMP CANCEL”.  
You can listen to your telephone calls from  
the speakers connected to this unit.  
When listening to your calls on your car  
speakers, you can adjust the volume by  
pushing the [P.CH] button upward or  
downward.  
3-1. Push the [P.CH] button upward or  
downward to select “ON” or “OFF”.  
• ON:  
• MUTE:  
Use with connected AMP.  
• OFF:  
Use with inside AMP.  
The sound from this unit is muted during  
telephone calls.  
Note:  
Setting the car speaker output for the  
cellular phone  
When the AUX input cable is used to connect a  
AUX BLUETOOTH BB (BLT370) (sold  
separately).  
The factory default setting is “R”.  
To output the telephone calls, set the cellular  
phone interrupt to ON.  
• If connecting a hands-free kit, please ensure the  
setting is ON to receive the telephone audio  
through the system.  
Performing a system check  
2-1. Select “SYSTEM CHECK”.  
3-1. Press and hold the [  
second or longer.  
] button for 1  
SYSTEM CHECK” appears in the display,  
then the unit returns to the speaker system  
selecting mode.  
2-1. Select “TEL-SPEAKER”.  
3-1. Push the [P.CH] button upward or  
downward to select “R” or “L”.  
• R:  
Telephone calls can be heard on the front  
right speaker connected to this unit.  
• L:  
Telephone calls can be heard on the front  
left speaker connected to this unit.  
28  
DXZ775USB  
Operations Common to Each Mode  
AUX function  
This system has an external input cable so you  
can listen to sounds and music from external  
devices connected to this unit.  
6. Push the [SEEK PANEL] leftward or  
rightward to move the cursor.  
7. Press the [MENU] button to select a  
character type. Each time you press the  
[MENU] button, the character type changes  
in the following order:  
Selecting AUX IN sensitivity  
Make the following settings to select the  
sensitivity when sounds from external devices  
connected to this unit are difficult to hear even  
after adjusting the volume.  
The factory default setting is “MID”.  
1. Press the [OPTION] button, “AUX SENSE  
Capital letters Small letters Numbers/  
Symbols Umlaut Capital letters…  
8. Push the [P.CH] button upward or downward  
to select the desired character.  
9. Repeat steps 6 to 8 to enter up to 10  
characters for the title.  
MID” appears in the display.  
10.Press and hold the [  
] button for 2  
2. Push the [P.CH] button upward or downward  
seconds or longer to store the title into  
memory.  
to select “LOW”, “MID” or “HIGH”.  
Entering titles  
Clearing titles  
1. Select and play a CD in the CD changer or  
tune in to a TV station for which you want to  
clear the title.  
Titles up to 10 characters long can be stored in  
memory and displayed for CD, CD changer and  
TV stations. The number of titles that can be  
entered for each mode are as follows.  
2. Press the [OPTION] button.  
Mode  
Number of titles  
30 titles  
3. Push the [SEEK PANEL] leftward or  
Radio mode  
CD mode  
TV mode  
rightward to select “TITLE INPUT”.  
50 titles  
4. Press the [  
] button.  
20 titles  
The display switches to the title input display.  
CD changer mode  
Number of titles  
5. Press and hold the [MENU] button for 1  
second or longer.  
DCZ625 connected  
100 titles  
All characters in the title disappear.  
1. Press the [SRC] button to select the mode  
you want to enter a title (CD, CD changer or  
TV).  
6. Press and hold the [  
] button for 2  
seconds or longer to store the setting.  
2. Select and play a CD in the CD changer or  
tune in to a TV station for which you want to  
enter the title.  
3. Press the [OPTION] button.  
4. Push the [SEEK PANEL] leftward or  
rightward to select “TITLE INPUT”.  
5. Press the [  
] button.  
The display switches to the title input display.  
DXZ775USB  
29  
7. OPERATIONS OF ACCESSORIES  
USB Operations  
• To prevent the accidental loss of data, always  
back up important data on your computer.  
USB memory device operation  
Note:  
• This unit does not support connections to a  
computer. In addition, connections made  
through a USB hub device are also not  
supported.  
• The following operations are the same as for CD  
mode:  
Pause  
Track selection  
Fast-forward/fast-backward  
Top function  
Scan play  
Repeat play  
Random play  
• When a USB memory device is composed of  
two or more drives, only one of the drives will  
be detected.  
• USB memory devices with security functions  
cannot be played.  
• Do not connect an iPod to the USB  
connector, since playback and controls may  
not function properly. To connect an iPod,  
use the CeNET iPod interface. For details,  
see the section “iPod BB Operations” (page  
32).  
Folder selection  
List search function  
See “CD/MP3/WMA/AAC Operations” (page 22-  
25) for details.  
About USB memory  
• USB is an acronym for Universal Serial Bus,  
and refers to an external bus standard  
supporting data transfer rates of 12 Mbps.  
• The order in which tracks are recorded may  
differ depending on the USB memory device  
connected (the actual playback order may not  
be the same as that indicated on your  
computer’s display).  
• This unit is compatible with USB 1.1/2.0 with  
maximum data transfer rates of 12 Mbps.  
CAUTION  
• USB memory devices that can be played by  
connecting to the unit’s USB cable are limited  
to those recognized as “USB mass storage  
class devices”; operation is not guaranteed  
with all USB memory devices.  
• Insert and remove a USB memory device  
only when the device is not being  
accessed. Connecting or disconnecting  
the device at the following times may  
result in the loss of data:  
Devices compatible with “USB Mass Storage  
Class” can be used merely by connecting to  
the host device, without need for special  
drivers or application software.  
- If the USB memory device is removed or  
power is disconnected during writing to  
the device.  
• Consult the manufacturer of your USB  
memory device for information regarding  
whether it is supported by “USB Mass  
Storage Class” standards.  
- When the device is subjected to static  
electricity or electric noise.  
• Do not leave a USB memory device  
unattended in an automobile. Exposure to  
direct sunlight or high temperatures may  
cause deformation or other malfunction of  
the USB memory device.  
• Audio files playable on this unit are limited to  
MP3/WMA/AAC files. For details, see the  
section “MP3/WMA/AAC” (page 22).  
Copy-protected WMA/AAC files cannot be  
played on this unit.  
30  
DXZ775USB  
USB Operations  
Connecting a USB memory device  
To stop play  
1. Connect the USB memory device to the USB  
1. Press the [SRC] button and switch the  
function to a source other than the USB  
memory.  
cable.  
Playback will begin from the first file  
recorded on the USB memory device.  
If the USB memory device is not recognized,  
press the [SRC] button to switch the source to  
the device.  
Always insert the USB memory device fully  
into the connector. Incomplete connections  
may cause the USB memory device not to be  
recognized.  
Depending on the number of tracks recorded,  
some amount of time may be required until all  
tracks are read into the unit.  
CAUTION  
Do not remove the USB memory device  
when the USB mode is selected, since it may  
result in loss or damage to data on the USB  
memory device.  
Always backup and save important data on  
your computer.  
2. Remove the USB memory device from the  
USB cable.  
The order in which tracks are recorded may  
differ depending on the USB memory device  
connected (the actual playback order may not  
be the same as that indicated on your  
computer’s display).  
To listen to tracks on a connected  
USB memory device  
1. Press the [SRC] button to switch the source.  
When USB memory device is selected,  
playback will begin from the location at which  
playback was previously stopped.  
When a USB memory device is connected the  
USB mode will be displayed.  
When a USB memory device is disconnected  
and then reconnected, playback will begin  
from the beginning of the USB memory  
device.  
DXZ775USB  
31  
iPod BB Operations  
iPod BB  
Other various play functions  
(in Play mode)  
This section describes operations when  
connected to a CeNET iPod Interface (EA-  
1276B). (Hereinafter, “iPod Interface (EA-  
1276B)” is abbreviated as iPod BB.)  
Notes:  
• These functions are not supported when in the  
iPod menu mode.  
• The Random function set on the iPod or when  
connected to iPod BB, remains the same after  
attachment/ detachment of the iPod.  
Note:  
• See the iPod BB Owner’s Manual for details  
regarding iPod BB connections and operation  
conditions.  
• The iPod BB can be set simultaneously for All  
repeat and All random.  
Connecting an iPod  
1. Press the [OPTION] button.  
When an iPod is connected to the iPod BB  
interface, the “Repeat” set on the iPod will  
become “All repeat play” instead. Likewise,  
“Shuffle” set on the iPod will become as follows:  
Repeat play  
Play back one track repeatedly.  
2. Push the [SEEK PANEL] leftward or  
rightward to select “RPT”.  
• “Shuffle (Albums)” play Random play  
3. Push the [P.CH] button upward or downward  
• “Shuffle (Songs)” play All random play  
to select “ ”, and then press the [  
button to perform repeat play.  
]
The iPod BB interface has two modes, the “Play  
mode” and the “iPod menu mode” for selecting  
tracks. Switch between these modes by  
pressing the [MENU] button.  
All repeat play  
Repeatedly play all tracks within a selected  
category.  
2. Push the [SEEK PANEL] leftward or  
Select iPod BB Interface  
rightward to select “RPT”.  
1. Press the [SRC] button.  
3. Push the [P.CH] button upward or downward  
to select “ALL”, and then press the  
Playback will begin from the last file that was  
played on the iPod alone or through the iPod  
BB.  
[
] button to perform all repeat play.  
Random play  
Note:  
Play all albums within a selected category, in  
random order. (Corresponds to “Shuffle  
(Albums)” command on iPod.)  
• The following operations in Play mode operate  
the same as in CD mode:  
Track selection: [SEEK PANEL]  
Fast-forward/fast-backward: [SEEK PANEL]  
2. Push the [SEEK PANEL] leftward or  
rightward to select “RDM”.  
Pause: [  
]
3. Push the [P.CH] button upward or downward  
See “CD/MP3/WMA/AAC Operations” (page 22-  
25) for details.  
to select “ ”, and then press the [  
button to perform random play.  
]
All random play  
Play all tracks within a selected category, in  
random order. (Corresponds to “Shuffle  
(Songs)” command on iPod.)  
2. Push the [SEEK PANEL] leftward or  
rightward to select “RDM”.  
3. Push the [P.CH] button upward or downward  
to select “ALL”, and then press the  
[
] button to perform all random  
play.  
32  
DXZ775USB  
iPod BB Operations  
To cancel the trick play  
2. Push the [SEEK PANEL] leftward or  
rightward to select “RPT OFF” or “RDM  
OFF”.  
About title display  
This unit supports the display of title information  
transmitted from a connected iPod.  
• Character code information is UTF-8;  
displayable characters include English  
alphanumerics, some symbols, and some  
umlaut characters.  
3. Press the [  
] button.  
Note:  
• When the all repeat play mode is canceled,  
playback will stop when all tracks have been  
played.  
• Unsupported characters will be replaced by  
asterisks (*).  
Selecting category from the iPod  
menu  
1. Press the [MENU] button.  
The iPod menu categories will be displayed.  
2. Push the [P.CH] button upward or downward  
to switch between categories.  
The iPod menu categories alternate in the  
following order:  
ComposersPlaylistArtists↔  
AlbumsSongsGenres↔  
Composers” ...  
Note:  
The iPod menu mode can be canceled by  
performing the following operation:  
• Press the [MENU] button.  
3. Push the [SEEK PANEL] rightward to select  
the category.  
4. When the track name display is showing,  
push the [SEEK PANEL] rightward.  
Playback will begin from the first track in the  
selected category, and the iPod menu mode  
will be canceled.  
Subfolders may be displayed, depending on  
the category.  
In this case, push the [P.CH] button upward or  
downward to switch between subfolders, then  
push the [SEEK PANEL] rightward to select  
the desired subfolder.  
When the track name display is showing,  
pushing the [SEEK PANEL] leftward will  
return to the currently playing folder name  
display.  
5. Push the [P.CH] button upward or downward  
to select a track within a category.  
6. Push the [SEEK PANEL] rightward to play  
the desired track.  
DXZ775USB  
33  
Satellite Radio Operations  
This function is available when a Satellite Radio  
Receiver is connected through the CeNET  
cable.  
Confirming your SIRIUS ID  
1. Press the [OPTION] button.  
2. Push the [SEEK PANEL] leftward or  
This unit can control the following satellite radio  
receivers:  
rightward to select “SID DISP”.  
3. Press the [  
] button.  
• XM Satellite Radio Receiver: XMD1000  
• XM Smart Digital Adapter: XM SDA  
Your SIRIUS ID will be displayed 12 digits  
number.  
• SIRIUS Satellite Radio Receiver: SIRCL2,  
SIRCL3  
Note:  
4. To return to the previous mode, press the  
[OPTION] button.  
• When the function is differ depending to the  
connected receiver, they are distinguished by the  
following notations:  
“XM”: for an XM Satellite Radio Receiver  
“SIRIUS”: for a SIRIUS Satellite Radio Receiver  
Displaying channel labels  
1. Press the [TITLE] button to select the  
desired channel label.  
Channel Category Title Artist ➜  
Radio text Channel...  
Selecting a Satellite Radio mode  
1. Press the [SRC] button.  
Channel selection  
1. Channels are selected with the [SEEK  
The system changes to the specified  
Satellite Radio mode.  
PANEL].  
For details, see the following operation  
descriptions.  
Selecting a band  
Note:  
1. Press the [MENU] button to select a band.  
This changes the reception band as follows:  
XM: XM1 XM2 XM3 XM1 ...  
SIRIUS: SR1 SR2 SR3 SR1 ...  
• The audio output is muted and other button  
operations are not accepted during channel  
selection.  
Information displayed during reception  
The following information is displayed when the  
satellite radio cannot be received normally.  
Tuning mode  
There are two channel selection modes: quick  
tuning mode and step tuning mode.  
• When the receiver is turned on the first time  
or after a reset: “UPDATING”  
Quick tuning  
1. Push the [SEEK PANEL] leftward or  
rightward and hold in position for 1 second or  
longer.  
• When a channel is being tuned in (no signal is  
yet received):  
XM: “LOADING”, SIRIUS: “ACQUIRING”  
Step tuning  
1. Push the [SEEK PANEL] leftward or  
rightward.  
• A channel without a broadcast has been  
selected:  
XM: “– – – CH”, SIRIUS: “INVALID CH”  
• A channel not covered by your contract:  
XM: “UPDATING”, SIRIUS: “CALL 888↔  
539-SIRI” (alternated)  
• When your contract is expired: “SUB  
UPDATE”  
34  
DXZ775USB  
Satellite Radio Operations  
Recalling a preset station  
Scan function  
A total of 18 satellite radio stations can be  
There are two scan modes: the category scan  
stored.  
mode and the preset scan mode.  
XM: 6-XM1, 6-XM2 and 6-XM3  
During scanning channels are displayed in  
abbreviated form, the display mode cannot be  
switched.  
SIRIUS: 6-SR1, 6-SR2 and 6-SR3  
This allows you to store your favorite satellite  
radio stations in memory for later recall.  
Category scan (CATEGORY SCN)  
In a category scan, broadcast channels in the  
same category as the current channel are  
selected about every 10 seconds.  
1. Press the [MENU] button to select the  
desired band.  
2. Push the [P.CH] button upward or downward  
1. Press the [OPTION] button.  
to select the desired preset station.  
2. Push the [SEEK PANEL] leftward or  
rightward to select “CATEGORY SCN”.  
Preset memory  
1. Press the [MENU] button to select the  
3. Press the [  
] button.  
Note:  
desired band.  
• Category scanning is not available when no  
category is defined for the current channel.  
2. Select the desired channel with quick tuning  
or step tuning.  
Preset scan (PRESET SCN)  
A preset scan scans the channels (up to 18  
channels) stored in the preset memory about  
every 10 seconds.  
3. Press the [  
] button to enter the  
P.CH memory screen.  
4. Push the [P.CH] button upward or downward  
to select the desired preset channel.  
1. Press the [OPTION] button.  
5. Press and hold the [  
] button for 2  
2. Push the [SEEK PANEL] leftward or  
seconds or longer to store the current  
channel into preset memory.  
rightward to select “PRESET SCN”.  
3. Press the [  
] button.  
Receiving stations selected by  
category  
Satellite Radio allows you to select broadcast  
channel category (contents).  
1. Press and hold the [MENU] button for 1  
second or longer to select the category  
selection mode.  
It press once again, return to the channel  
selection mode.  
2. Push the [P.CH] button upward or downward  
to change the category item.  
3. Push the [SEEK PANEL] leftward or  
rightward to tune in a station.  
Note:  
• When the category selection mode is entered, the  
category of the last received channel is displayed  
first.  
• The category selection mode is canceled when  
no channel with the selected category can be  
found.  
• If the [SEEK PANEL] are not pushed within 7  
seconds, the category selection mode is  
canceled, and resumes to the channel mode.  
DXZ775USB  
35  
CD Changer Operations  
Note:  
Displaying CD titles  
This unit can display title data for CD-text CDs  
and user titles input with this unit.  
• The following operations are the same as for CD  
mode:  
Pause  
Track selection  
Fast-forward/fast-backward  
Scan play  
1. Press and hold the [TITLE] button for 1  
second or longer to display the title.  
2. Press the [TITLE] button to change the title  
display.  
Repeat play  
Random play  
See “CD/MP3/WMA/AAC Operations” (page 22-  
25) for details.  
Procedure to scroll a title  
Set “AUTO SCROLL” to “ON” or “OFF”.  
(The factory default setting is “ON”. Refer to the  
subsection “Setting the method for title scroll”  
in section “Operations Common to Each  
Mode”.)  
CD changer functions  
When an optional CD changer is connected  
through the CeNET cable, this unit controls all  
CD changer functions. This unit can control a  
total of 2 changers.  
When set to “ON”  
The title is automatically kept scrolling.  
When set to “OFF”  
To scroll just 1 time.  
Note:  
Press the [SRC] button and select the CD  
changer mode to start play. If 2 CD changers  
are connected, press the [SRC] button to select  
the CD changer for play.  
• User title can’t scroll.  
If “NO MAGAZINE” appears in the display, insert  
the magazine into the CD changer. “DISC  
CHECK” appears in the display while the player  
loads (checks) the magazine.  
If “NO DISC” appears in the display, eject the  
magazine and insert discs into each slot. Then,  
reinsert the magazine back into the CD changer.  
Selecting a CD  
1. Push the [P.CH] button upward or downward  
to select a desired disc in the magazine.  
If a CD is not loaded in a slot of magazine,  
NO DISC” appears in the display  
Note:  
• Some CDs recorded in CD-R/CD-RW mode may  
not be usable.  
CAUTION  
CD-ROM discs cannot be played from every  
CD changer, it’s depended on the model.  
36  
DXZ775USB  
CD Changer Operations  
Disc random play  
Other various play functions  
The disc random play selects and plays  
individual tracks or discs automatically in no  
particular order. This function continues  
automatically until it is cancelled.  
Disc scan play  
Disc scan play locates and plays the first 10  
seconds of the first track on each disc in the  
currently selected CD changer. This function  
continues automatically until it is cancelled.  
1. Press the [OPTION] button.  
2. Push the [SEEK PANEL] leftward or  
Disc scan play is useful when you want to select a  
desired CD.  
rightward to select “RDM”.  
3. Push the [P.CH] button upward or downward  
1. Press the [OPTION] button.  
to select “ALL”, and then press the  
2. Push the [SEEK PANEL] leftward or  
[
] button. “DISC RDM” appears in  
rightward to select “SCN”.  
the display and disc random play starts.  
3. Push the [P.CH] button upward or downward  
To cancel the trick play  
1. Press the [OPTION] button.  
to select “ALL”, and then press the  
[
] button. “DISC SCN” appears in  
the display and disc scan play starts.  
2. Push the [SEEK PANEL] leftward or  
rightward to select “TRICK OFF”.  
Disc repeat play  
3. Press the [  
trick play.  
] button to cancel the  
After all the tracks on the current disc have been  
played, disc repeat play automatically replays  
the current disc over from the first track. This  
function continues automatically until it is  
cancelled.  
1. Press the [OPTION] button.  
2. Push the [SEEK PANEL] leftward or  
rightward to select “RPT”.  
3. Push the [P.CH] button upward or downward  
to select “ALL”, and then press the  
[
] button. “DISC RPT” appears in  
the display and disc repeat play starts.  
DXZ775USB  
37  
DVD Changer Operations  
Note:  
By connecting an optional DVD changer that  
supports CeNET wiring, this unit can be used to  
control the DVD changer. To view DVDs, an  
optional monitor is required.  
• The following operations are the same as for CD  
and CD Changer modes:  
Pause  
Track selection  
Fast-forward/fast-backward  
Scan play  
Repeat play  
Random play  
See “CD/MP3/WMA/AAC Operations” (page 22-  
25) and “CD Changer Operations” (page 36-37)  
for details.  
• The DVD control and display functions  
supported by this unit are limited; the unit  
does not support all the functions possible on  
a DVD changer.  
For fullest functionality, use the remote  
control unit provided with your DVD changer  
to control its operations. For details, consult  
the Owner’s Manual provided with your DVD  
changer.  
38  
DXZ775USB  
TV Operations  
Note:  
Setting the TV diver  
You can change the reception setting for the TV  
antenna connected to the TV tuner.  
• The following operations are performed the same  
as for radio mode:  
Channel selection  
Storing channels in memory  
Calling channels from memory  
Auto store  
1. Press the [OPTION] button to switch to the  
adjustment selection display.  
2. Push the [SEEK PANEL] leftward or  
rightward to select “TV DIVER”.  
Preset scan  
See “Radio Operations” (page 20-21) for details.  
3. Push the [P.CH] button upward or downward  
to set to “ON” or “OFF”.  
• ON:  
TV tuner functions  
Sets the diver setting to ON.  
• OFF:  
Sets the diver setting to OFF.  
When an optional TV tuner is connected  
through the CeNET cable, this unit controls all  
TV tuner functions. To watch TV requires a TV  
tuner and monitor.  
4. Press the [OPTION] button to return to the  
previous mode.  
Watching a TV  
1. Press the [SRC] button and select the TV  
mode.  
2. Press the [MENU] button to select the  
desired TV band (TV1 or TV2). Each time the  
button is pressed, the input selection toggles  
between TV1 and TV2.  
3. Push the [SEEK PANEL] leftward or  
rightward to tune in the desired TV station.  
Watching a video  
The TV tuner has a VTR input terminal to which  
1 external device can be connected. Connect a  
12 V video cassette player (VCP) or video  
cassette recorder (VCR) to the TV tuner input  
terminal.  
1. Press the [OPTION] button.  
2. Push the [SEEK PANEL] leftward or  
rightward to select “TV/VTR”.  
3. Press the [  
mode.  
] button to enter the VTR  
4. To return to the TV broadcast, press the  
[OPTION] button.  
5. Press the [  
TV mode.  
] button to return to the  
DXZ775USB  
39  
8. IN CASE OF DIFFICULTY  
Problem  
Cause  
Measure  
Power does not  
turn on.  
Fuse is blown.  
Replace with a fuse of the same amperage. If the fuse  
blows again, consult your store of purchase.  
(No sound is  
produced.)  
Incorrect wiring.  
Consult your store of purchase.  
No sound output Power antenna lead is  
1. Turn the unit off.  
when operating  
the unit with  
amplifiers or  
power antenna  
attached.  
shorted to ground or  
2. Remove all wires attached to the power antenna  
lead. Check each wire for a possible short to  
ground using an ohm meter.  
excessive current is required  
for remote-on the amplifiers  
or power antenna.  
3. Turn the unit back on.  
4. Reconnect each amplifier remote wire to the power  
antenna lead one by one. If the amplifiers turn off  
before all wires are attached, use an external relay  
to provide remote-on voltage (excessive current  
required).  
Nothing happens The microprocessor has  
Turn off the power, then press  
Reset button  
when buttons are malfunctioned due to noise, the [RELEASE] button and  
pressed.  
etc.  
remove the DCP.  
Press the reset button for about  
2 seconds with a thin rod.  
Display is not  
accurate.  
DCP or main unit connectors Wipe the dirt off with a soft cloth moistened with  
are dirty. cleaning alcohol.  
No sound heard  
No sound heard  
The speaker protection circuit 1. Turn down sound volume. Function can also be  
is operating.  
restored by turning the power off and on again.  
(Speaker volume is reduced automatically when  
the speaker protection circuit operates).  
2. If the sound is muted again, consult our service  
department.  
MP3/WMA/AAC files are  
absent in a disc.  
Write MP3/WMA/AAC files onto the disc properly.  
Files are not recognized as  
an MP3/WMA/AAC file.  
Use MP3/WMA/AAC files encoded properly.  
File system is not correct.  
Use ISO9660 level 1, 2 or JOLIET or Romeo or  
APPLE ISO file system.  
Sound skips or is Compact disc is dirty.  
Clean the compact disc with a soft cloth.  
noisy.  
Compact disc is heavily  
Replace with a compact disc with no scratches.  
scratched or warped.  
Sound is cut or  
skipped.  
MP3/WMA/AAC files are not Use MP3/WMA/AAC files encoded properly.  
encoded properly.  
Noise is  
generated or  
noise is mixed  
with sound.  
Sound is bad  
directly after  
power is turned  
on.  
Water droplets may form on Let dry for about 1 hour with the power on.  
the internal lens when the car  
is parked in a humid place.  
Wrong filename  
File system is not correct.  
Use ISO9660 level 1, 2 or JOLIET or Romeo or  
APPLE ISO file system.  
40  
DXZ775USB  
Problem  
Cause  
Measure  
No sound heard. The USB memory device  
Record MP3/WMA/AAC files properly to the USB  
contains no MP3/WMA/AAC memory device.  
files.  
The files are not proper MP3/ Use only properly encoded MP3/WMA/AAC files.  
WMA/AAC format.  
Files are DRM copyright  
protected.  
See page 22 for details on how to cancel DRM  
protection.  
Connectors are loose.  
Disconnect the USB memory device and reconnect  
securely.  
Sound is  
The MP3/WMA/AAC files are Use only properly encoded MP3/WMA/AAC files.  
interrupted or has improperly encoded.  
noise.  
USB memory  
device isn’t  
recognized.  
The USB memory device is Disconnect the USB memory device and reconnect. If  
damaged.  
the device is still not recognized, try replacing with a  
different USB memory device.  
Connectors are loose.  
Can’t insert USB The USB memory devices  
Try reversing the connection direction of the USB  
memory device.  
has been inserted improperly. device (usually the brand name surface should be  
facing left).  
The USB connector is  
broken.  
Replace with a new USB memory device.  
DXZ775USB  
41  
9. ERROR DISPLAYS  
If an error occurs, one of the following displays is displayed.  
Take the measures described below to eliminate the problem.  
Error Display  
ERROR 2  
Cause  
A CD is caught inside the CD This is a failure of CD deck’s mechanism and consult  
deck and is not ejected. your store of purchase.  
Measure  
ERROR 3  
ERROR 6  
A CD cannot be played due Replace with a non-scratched, non-warped-disc.  
to scratches, etc.  
A CD is loaded upside-down Eject the disc then reload it properly.  
inside the CD deck and does  
not play.  
ERROR 2  
ERROR 3  
A CD inside the CD changer This is a failure of CD changer’s mechanism and  
is not loaded.  
consult your store of purchase.  
A CD inside the CD changer Replace with a non-scratched, non-warped disc.  
cannot be played due to  
scratches, etc.  
ERROR 6  
A CD inside the CD changer Eject the disc then reload it properly.  
cannot be played because it  
is loaded upside-down.  
ERROR 2  
ERROR 3  
ERROR 6  
A DISC inside the DVD  
changer cannot be played.  
This is a failure of DVD mechanism and consult your  
store of purchase.  
A DISC cannot be played due Retry or replace with a non-scratched, non-warped-  
to scratches, etc.  
disc.  
A DISC inside the DVD  
changer cannot be played  
because it is loaded upside-  
down.  
Eject the disc then reload it properly.  
ERROR P  
ERROR R  
ERROR 1  
Parental level error  
Region code error  
Set the correct Parental level.  
Eject the disc and replace correct region code disc.  
Disconnect the iPod, then connect it again.  
A communication error  
occurs between the iPod and  
the iPod CeNET Controller.  
NO IPOD  
ERROR 1  
There is no iPod connected. Please connect the iPod.  
Device mechanism is  
damaged.  
The unit’s mechanism may be damaged. Consult  
your dealer.  
NO FILE  
USB memory device contains Insert USB memory device containing audio files.  
no audio files.  
DSP ERROR  
USB connector is short-  
circuited or USB memory  
device is overloaded.  
Disconnect USB memory device, then hold [SRC]  
button depressed to turn power OFF. Then press  
[SRC] button once again to turn power ON.  
If an error display other than the ones described above appears, press the reset button. If the problem  
persists, turn off the power and consult your store of purchase.  
42  
DXZ775USB  
10.SPECIFICATIONS  
FM Tuner  
General  
Frequency Range: 87.9 MHz to 107.9 MHz  
Power Supply Voltage:  
Usable Sensitivity: 9 dBf  
14.4 V DC (10.8 to 15.6 V allowable), negative  
ground  
50dB Quieting Sensitivity: 15 dBf  
Alternate Channel Selectivity: 70 dB  
Stereo Separation (1 kHz): 35 dB  
Frequency Response ( 3 dB): 30 Hz to 15 kHz  
Current Consumption: Less than 15 A  
Speaker Impedance: 4 (4 to 8 allowable)  
Auto Antenna Rated Current: 500 mA or less  
Weight / Source unit: 2.75 lb. (1.6 kg)  
Weight / Remote control unit:  
AM Tuner  
Frequency Range: 530 kHz to 1710 kHz  
1.41 oz. (40 g) (including battery)  
Dimensions / Source unit:  
Usable Sensitivity: 25 µV  
7" (Width) 2" (Height) 6-1/8" (Depth)  
[178 (W) 50 (H) 158 (D) mm]  
Dimensions / Remote control unit:  
CD Player  
System: Compact disc digital audio system  
1-3/4" (Width) 4-5/16" (Height) 7/16"  
(Depth)  
Usable Discs: Compact disc  
Frequency Response ( 1 dB): 5 Hz to 20 kHz  
Dynamic Range (1 kHz): 95 dB  
Harmonic Distortion: 0.01%  
[44 (W) 113 (H) 11 (D) mm]  
Power Output :  
20 W RMS x 4 Channels at 4 Ω  
and 1 % THD+N  
Audio  
Signal to Noise Ratio:  
84 dBA (reference: 1 W into 4 )  
Maximum Power Output: 212 W (53 W 4 ch)  
Bass Control Action (80 Hz): +12 dB, –12 dB  
Treble Control Action (10 kHz): +12 dB, –12 dB  
Line Output Level (CD 1 kHz): 5.8 V  
Note:  
• Specifications and design are subject to change without notice for further improvement.  
DXZ775USB  
43  
Clarion Co., Ltd.  
PE-2899B  
280-8465-00  
All Rights Reserved. Copyright © 2006: Clarion Co., Ltd.  
Printed in China / Imprimé en Chine / Impreso en China  
2006/12  

Nokia 2115i User Manual
Motorola Nextel i850 User Manual
LG Electronics Viewty KU990 User Manual
Kenwood KDC W6527SE User Manual
HTC KII0160 User Manual
Grindmaster SHUTTLE BREWER APBVSA 430V2E230 User Manual
Emerson Clock EE542 1Z User Manual
COBY electronic CD RA195 User Manual
Blackberry Pearl 8220 User Manual
Alpine CDE 9870 User Manual