EMERSON QUIET KOOL EATC08RE1 User Manual

EATC08RE1  
EATC10RE1  
EATC10RE2  
EATC12RE1  
EATC12RE2  
EATE12RD2  
EATC14RD2  
EATH14RD2  
Handling the remote controller  
CONTENTS  
T
E
M
P
/
T
I
M
E
R
E
S
n
a
e
v
r
e
g
r
y
T
E
M
P
/
T
I
M
E
R
S
l
e
e
p
C
F
h
i
   c
F
o
M
l
l
e
o
w
A
C
u
o
t
o
Location of the remote controller.  
o
n
o
f
f
o
l
M
o
d
e
A
u
g
t
o
D
r
y
F
a
n
H
i
h
H
e
a
t
T
i
m
e
r
O
n
/
o
f
f
F
a
n
M
e
d
L
o
w
Use the remote controller within a distance of 5  
meters from the appliance, pointing it towards  
the receiver. Reception is confirmed by a beep.  
Handling the remote controller ......................................................  
Remote controller Specifications...................................................  
Function buttons .................. ..........................................................  
2
3
4
5m  
How to use the buttons ...................................................................  
Auto operation.............................................................................................................  
Cooling/Heating/Fan operation..................................................................................  
Dehumidifying operation ...........................................................................................  
Timer operation .........................................................................................................  
Energy saving operation ...........................................................................................  
5
5
5
6
CAUTIONS  
The air conditioner will not operate if curtains, doors or other materials block  
the signals from the remote controller to the unit.  
Prevent any liquid from falling into the remote controller. Do not expose the  
remote controller to direct sunlight or heat.  
If the infrared signal receiver on the indoor unit is exposed to direct sunlight,  
the air conditioner may not function properly. Use curtains to prevent the  
sunlight from falling on the receiver.  
If other electrical appliances react to the remote controller, either move these  
appliances or consult your local dealer.  
7
9
WARNING:  
Chemical Burn Hazard. Keep batteries away from children.  
This product contains a lithium button/coin cell battery. If a new or  
used lithium button/coin cell battery is swallowed or enters the body,  
it can cause severe internal burns and can lead to death in as little as  
2 hours. Always completely secure the battery compartment. If the  
battery compartment does not close securely, stop using the product,  
remove the batteries, and keep it away from children. If you think  
batteries might have been swallowed or placed inside any part of the  
body, seek immediate medical attention.  
Installation instructions of battery  
Step 1: Inserta coin verticallyin the groove  
on the batterycover, clockwise rotation of 45  
degrees, make surethat the grooveis aligned  
with the "unlock" sign as shownbelow  
Step 3: Installthe battery cover, make  
sure the batterycover groove isaligned  
with the "unlock" sign. Insert acoin  
vertically in thegroove and pressit  
gently, thencounter clockwise rotation  
of 45 degrees, make sure thegroove is  
aligned with the"lock" sign asshown  
and remove thebattery cover.  
Lock sign  
The cells shall be disposed of properly, including keeping them away  
from children. Even used cells may cause injury.  
Lock sign  
Coin  
Coin  
Unlock sign  
below.  
Battery cover  
Unlock sign  
Lock sign  
Groove  
Groove  
Battery cover  
Lock sign  
Coin  
Unlock sign  
Coin  
Unlock sign  
Battery cover  
Battery cover  
Step 2: Installbattery inside theremote  
controller, thepositive (+) sideup.  
Groove  
Groove  
WARNING  
1. Battery must bedisposed of properly. Do not  
short circuit or disposeof in the fire.  
2. Keep batteries outof the reach ofchildren.  
3. Caution for ingestion.  
Positive (+) side up  
Battery  
4. Non-rechargeable batteries arenot to be  
recharged.  
5. Exhausted batteries areto be removed from  
the product.  
1
2
Function buttons  
Remote Controller Specifications  
MODE button  
Press this button to  
select the desired  
operation mode.  
Model  
RG15A(B)/E, RG15A3(B)/E, RG15A4(B)/E, RG15A5(B)/E,  
ON/OFF button  
Operation starts when this button is  
pressed and stops when the button  
is pressed again.  
Rated Voltage  
3.0V( Lithium battery CR2025)  
2.4V  
Lowest Voltage of  
CPU Emitting Signal  
NOTE: If the unit has ENERGY  
SAVER function,it wil l ini tia te  
automatically the Energy Saver  
function under Cool, Dry, and  
Auto(only Auto-Cooling and  
Auto-Fan) modes.  
5m  
Signal Receiving Range  
Environment  
-5OC~60OC(23OF~140OF)  
TEMP UP button  
TEMP DOWN button  
NOTE:  
-Buttons design is based on typical model and might be slightly different  
from the actual one you purchased, the actual shape shall prevail.  
-All the functions described are accomplished by the unit, if the unit has  
no this feature, there is no corresponding operation happened when  
press the relative button on the remote controller.  
Push this button to  
decrease the indoor  
temperature setting.  
Push this button to  
increase the temper-  
ature setting.  
-When there are wide differences between Remote controller Illustration  
and USERS MANUALon function description, the description on USERS  
MANUAL shall prevail.  
TIMER button  
FAN button  
Push this button to  
activate the "Auto  
Start" or "Auto Stop"  
program.  
Used to select the  
desired fan speed.  
ONE TOUCH button  
SLEEP button  
Push this button, the  
Press this button to  
activate the Sleep  
system will automatically  
shift to COOL operation  
with auto fan speed, the  
setting temperature is  
26OC/80OF. And the timer  
setting program will be  
cancelled.(on some models)  
mode. This function is  
available on COOL,  
HEAT orAUTO mode  
only and maintain the  
most comfortable  
temperature for you  
and save enrgy. For  
, ,  
the detail, see sleep  
,,  
RG15A(B)/E  
RG15A4(B)/E  
RG15A5(B)/E  
RG15A3(B)/E  
ENERGY SAVER button  
operation in  
,,  
, ,  
,
Press this button to  
activate the Energy-  
saving mode. Press  
it again to stop the  
funtion.(on some  
models)  
USER S MANUAL.  
3
4
Dehumidifying operation  
How to use the buttons  
Auto operation  
Ensure the unit is plugged in and power is  
available.  
1. Press the ON/OFFbutton to start the air  
conditioner.  
2. Press the MODE button to select Dry.  
3. Press the TEMP UP/DOWN button to  
set the desired temperature.  
2
1
2
3
3
1
Ensure the unit is plugged in and power is  
available.  
1. Press the ON/OFFbutton to start the air  
conditioner.  
3
3
2. Press the MODE button to select Auto.  
3. Press the TEMP UP/DOWN button to set  
the desired temperature.  
NOTE  
In the Dehumidifying mode, you can not switch the  
fan speed. It has already been automatically  
controlled.  
NOTE  
1. In the Auto mode, the air conditioner can logically  
choose the mode of Cooling, Fan, Heating and  
by sensing the difference between the actual  
ambient room temperature and the set temperature  
on the remote controller.  
2. In the Auto mode, you can not switch the fan speed.  
It has already been automatically controlled.  
3. If the Auto mode is not comfortable for you , the  
desired mode can be selected manually.  
Cooling /Heating/Fan operation  
Ensure the unit is plugged in and power is  
available.  
2
1
1. Press the ON/OFF button to start the air  
conditioner.  
3
3
2. Press the MODE button to select Cool, Heat  
(cooling&heating models only) or Fan mode.  
3. Press the TEMP UP/DOWN button to set the  
desired temperature.  
4
4. Press the FAN button to select the fan  
speed.  
NOTE  
In the Fan mode, you are not able to control the  
room temperature either. In this case, only step 1, 2  
and 4 may be performed.  
5
6
COMBINED TIMER  
(Setting both ON and OFF timers simultaneously)  
Timer operation  
Press the TIMER button can initiate the  
Auto-start and Auto-stop setting program  
of the unit.  
AUTO STOP  
(On Stop  
AUTO START  
Start operation)  
This feature is useful when you want to stop the  
air conditioner after you go to bed, and start it  
again in the morning when you wake up or when  
2
2
2
2
1
1
To set theAuto-start/stop time.  
you return home.  
Example:  
1. Press the TIMER button, when the TIMER  
ON indicator displayed on the LED window  
of the air conditioner, it indicates the Auto  
Start setting program is initiated. When the  
TIMER OFF indicator displayed on the LED  
window of the air conditioner, it indicates the  
Auto Stop setting program is initiated.  
2. Press or hold the Up( ) or Down( ) to  
change the Auto time. The control will count  
down the time remaining until start/stop.  
3. The selected time will register in 5 seconds  
and the air conditioner will automatically  
revert back to display the previous temper-  
ature setting.  
To stop the air conditioner 2 hours after setting  
and start it again 10 hours after setting.  
1. Press the TIMER button until the TIMER  
OFF indicator is displayed on the LED display  
of the air conditioner.  
2. Use the UP/DOWN button to display "2.0" on  
the LED display of the air conditioner.  
3. Press the TIMER button again to display the  
TIMER ON on the LED display of the unit.  
4. Use the UP/DOWN button to display "10" on  
the LED display of the unit.  
5. Wait for 5 seconds until the previous display  
revert back to the LED window.  
4. Turning the unit ON or OFF at any time  
will cancel the Auto Start/stop function.  
AUTO START ATUO STOP  
(Off  
Start  
Stop operation)  
NOTE: To cancel the TIMER setting, push  
the TIMER button and press or hold the Up  
This feature is useful when you want to start  
the air conditioner before you wake up and  
stop it after you leave the house.  
Example:  
( ) or Down( ) until 0 hour is displayed  
on the LCD window of the air conditioner.  
To start the air conditioner 5 hours after setting,  
and stop it 8 hours after setting.  
1. Press the TIMER button until the TIMER  
ON indicator is displayed on the LED display  
of the air conditioner.  
2. Use the UP/DOWN button to display  
"5.0" on the LED display of the air conditioner.  
3. Press the TIMER button again to display  
the TIMER OFF on the LED display of the unit.  
4. Use the UP/DOWN button to display  
"8.0" on the LED display of the unit.  
5. Wait for 5 seconds until the previous display  
revert back to the LED window.  
7
8
Energy saver operation  
NOTE:  
-Buttons design is based on typical model and might be slightly different  
In this mode, the fan will continue to  
run for 3 minutes after the compressor  
shuts off. The fan then cycles on for 2  
minutes at 10 minute intervals until the  
room temperature is above the set  
temperature, at which time the compre-  
ssor turns back on and cooling stars.  
from the actual one you purchased, the actual shape shall prevail.  
-All the functions described are accomplished by the unit, if the unit has  
no this feature, there is no corresponding operation happened when  
press the relative button on the remote controller.  
-When there are wide differences between Remote controller Illustration  
and USERS MANUALon function description, the description on USERS  
MANUAL shall prevail.  
1
-The device could comply with the local national regulations. In Canada,  
it should comply with CAN ICES-3(B)/NMB-3(B). In USA, this device  
complies with part 15 of the FCC Rules. Operation is subject to the  
following two conditions: (1) This device may not cause harmful interfe-  
rence, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
-This equipment has been tested and found to comply with the limits for  
a Class B digital device, pursuant to part 15 of the FCC Rules. These  
limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses  
and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will  
not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications not approved by the party responsible for  
compliance could void suers authority to operate the equipment.  
9
10  

Xpelair 91173aa User Manual
Whirlpool As12 User Manual
Sanyo N 220aaas User Manual
Samsung Aw1880a User Manual
Powerdsine Lx2206 User Manual
MAYTAG MDB7100AWW User Manual
MAKITA PLM5113N2 User Manual
LG 49UT570H0UA User Manual
DELL XPS M1330 User Manual
BROTHER HL L2310D 02 User Manual